03
06
1.3 Technical Characteristics
Table - 01
Picture - 02
8
5
0
m
m
2. Installation and Pre Operation
2.1 Installation
The Blender is to be installed onto a leveled surface approximately 850mm high.
The High Performance Industrial Blenders were developed to be used in both
voltages: 110V or 220V. Upon receiving the Blender adjust its voltage according to the
one of the power supply source using the Voltage Selector Switch located at the bottom
of the machine. Adjust it if necessary.
The feeding cord has two rounded pins and one grounding.
Grounding is mandatory before switching the machine ON.
2.2 Pre Operation
IMPORTANT
When installing the Cup Nº02 (Pic.01) in the machine be sure it is perfectly fitted.
The Cup can be fitted in the machine in any position; which guarantees a perfect
operation.
First of all check if the Blender is firm in its position. It is recommended to work
with the machine in a flat surface with approximately 850mm of height.
Before using the machine all parts that get in contact with food must be washed
with running water and neutral soap. To clean your Blender read item 3.3 Cleaning on
this Manual (pag.4).
Characteristics
Unit.
LS-04
LS-06
LS-08
LS-10
110 ou 220
110 ou 220
110 ou 220
110 ou 220
60
60
60
60
0,5
0,5
0,5
0,5
0,38
0,38
0,38
0,38
620
680
700
780
260
280
300
300
210
210
250
250
8,8
8,9
9,0
9,5
Voltage
Frequency
Power Rating
Consumption
Height
Width
Depth
Net Weight
Gross Weight
[V]
[Hz]
[CV]
[kW/h]
[mm]
[mm]
[mm]
[kg]
[kg]
9,6
9,9
10,1
10,5
[l]
[ rpm]
04
3500
06
3500
08
3500
10
3500
Cup Capacity
Rotation
4. General Safety Practices
The following safety instructions are addressed to both the operator of the
machine as well as the person in charge of maintenance. The machine has to be
delivered only in perfect conditions of use by the Distributor to the user. The user shall
operate the machine only after being well acquainted with the safety procedures
described in the present manual. READ THIS MANUAL WITH ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
Some parts of the electric devices are connected to high voltage points . These
parts when touched may cause severe electrical shocks or even be fatal.
Never touch commands such as buttons, switches and knobs with wet hands ,
wet clothes and/or shoes. By not following these instructions operator could be exposed
to severe electrical shocks or even to a fatal situation.
4.1.2 Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make
sure the Switch is easy to be reached when necessary. Before any kind of maintenance,
physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the
floor is clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be sure
the command is the correct one. Check this manual for further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to
be given for each operation step. Every step of the operation shall be taken only if a sign
has been made and responded.
IMPORTANT
If any item from the GENERAL SAFETY NOTIONS section is not applicable to
your product, please disregard it.
Use of abrasives:
Sponges or steel wool and carbon steel brushes, besides scratching the
surface and compromising the stainless steel protection, leave particles that rust and
react contaminating the stainless steel. That is why such products must not be used
for cleaning and sanitization. Scrapings made with sharp instruments or similar must
also be avoided.
Main substances that cause stainless steel corrosion:
Dust, grease, acid solutions such as vinegar, fruit juices, etc., saltern
solutions (brine), blood, detergents (except for the neutral ones), common steel
particles, residue of sponges or common steel wool, and also other abrasives.