Skyjack SJ85AJ Скачать руководство пользователя страница 46

Страница: 46 / 106

208932AEA

SJ85AJ

Section 4 – Pre-operation

Function Tests

4.3-4 Test Start/Function Enable/

Emergency Power Switch and All
Boom and Platform Functions

WARNING

Ensure that there are no personnel or obstructions

in test area and there is sufficient room for boom

to swing.

Ensure

emergency stop button is pulled

out.

Start engine.

Do not hold

start/function enable/

emergency power switch in function enable
position. Attempt to activate each boom and
platform switch.

▪

Result:

All boom and platform functions

should not operate.

Hold

start/function enable/emergency

power switch in function enable position and
activate each boom and platform function.

▪

Result:

Engine speed increases from idle to

intermediate. All boom and platform functions
should operate as selected.

4.3-5 Test Platform Self-leveling

Lower boom to stowed position.

Adjust platform to a level position using platform
leveling switch, which controls

tilting up or

tilting down of platform.

Fully raise

main boom.

▪

Result:

Platform should remain level at all

times and lifting speed should slow down
before boom reaches full height.

Fully lower

main boom.

▪

Result:

Platform should remain level at all

times.

HOUR METER

QUARTZ

Base Control Console

Start/Function Enable/

Emergency Power Switch

Off/Base/Platform Key

Switch

Emergency Stop

Содержание SJ85AJ











































































































Результаты поиска

Содержание SJ85AJ

Отзывы:

Похожие инструкции для SJ85AJ

Бренды по названию

Популярные бренды

Skyjack SJ85AJ, Руководство по эксплуатации

Результаты поиска

Содержание SJ85AJ

Отзывы:

Похожие инструкции для SJ85AJ

Бренды по названию

Популярные бренды