background image

SJ85 AJ 

213217AAA

 

13

Serial Number Nameplate

  Section 1 – About This Mobile Elevating Work Platform (MEWP)

1.3   Serial Number Nameplate

The serial number nameplate (refer to 

 

Section 8

), located at the rear of the MEWP, lists the 

following:

 

Model number

 

Type

 

Group

 

Serial number

 

High capacity zone and low capacity zone

 

Capacity and maximum number of persons

 

Maximum work platform height

 

Maximum wind speed

 

Maximum manual force

 

Machine weight

 

Voltage

 

Maximum incline

 

System pressure

 

Lift pressure

 

Model year

 

Year of manufacture

1.4   Responsibility for 

Maintenance

1.4-1  Operator’s responsibility for 

maintenance

 WARNING

Maintenance must be performed by trained and 

qualified/competent personnel who are familiar 

with mechanical procedures.

Death or serious injury could result from the use of 
a MEWP that is not properly maintained or kept in 
good working condition. 

The operator must be sure that the MEWP has been 

properly maintained and inspected before using it.

The operator must perform all the daily inspections 

and function tests found in

 

Section

 

4.4

, even if 

the operator is not directly responsible for the 
maintenance of this MEWP. 

1.4-2  Maintenance and inspection 

schedule

Refer to service manual for frequent/periodic (every 3 
months or 150 hours) and annual inspection details.

The actual operating environment of the MEWP may 

affect the maintenance schedule.

 WARNING

Use original or manufacturer-approved parts and 
components for the MEWP.

 NOTE

Refer to Skyjack’s website 

www.skyjack.com

 

for the latest service bulletins prior to performing 
frequent/periodic or annual inspections.

1.4-3  Owner’s inspections

It is the responsibility of the owner to arrange daily, 
quarterly (or 150 hours) and annual inspections of the 
MEWP. Refer to the service manual for recommended 
maintenance and inspection areas and intervals. A 
record of annual inspection is kept on a label located 
close to the base control console on the cowling (refer 

to 

Section 7.3

)

.

Содержание 213217AAA

















































































































Отзывы: