Skyjack 213217AAA Скачать руководство пользователя страница 44

Страница: 44 / 112

213217AAA

SJ85 AJ

Section 4 – Pre-operation

Visual & Daily Maintenance Inspections

Fuel leaks

▪

Ensure that there are no fuel leaks.

WARNING

Engine fuels are combustible. Inspect the MEWP
in an open, well-ventilated area away from heaters,

sparks and flames. Always have an approved fire

extinguisher within easy reach.

▪

Ensure fuel tank, hoses and fittings show
no visible damage and no evidence of fuel
leakage.

4.2-7 Base

Turret transportation lock

▪

Ensure turret transportation lock is unlocked,
there are no loose or missing parts and there
is no visible damage.

Drive axles

▪

Ensure front drive axle

and rear drive axle

are properly secured, there are no loose

or missing parts, all fittings and hoses are
properly tightened and there is no evidence of
hydraulic leakage.

Tie rod

▪

Ensure there are no loose or missing parts,
tie rod end studs are locked and there is no
visible damage.

Oscillating cylinder assembly

▪

Ensure oscillating cylinder assembly is
properly secured and there are no visible
gaps, loose or missing parts, all fittings and
hoses are properly tightened and there is no
evidence of hydraulic leakage.

NOTE

Oscillating axle is locked when MEWP is in low
speed (refer to

Figure 37)

Содержание 213217AAA

















































































































Результаты поиска

Содержание 213217AAA

Отзывы:

Похожие инструкции для 213217AAA

Бренды по названию

Популярные бренды

Skyjack 213217AAA, Руководство по эксплуатации

Результаты поиска

Содержание 213217AAA

Отзывы:

Похожие инструкции для 213217AAA

Бренды по названию

Популярные бренды