manualshive.com logo in svg

SKC 224-44XR, Руководство по обслуживанию

Поделиться
Скачать
SKC 224-44XR Скачать руководство пользователя страница 5

Universal Pump Service Manual

1

1

1

1

1

Introduction

Universal XR Sample Pumps

Universal XR Sample Pumps are pneumatic constant fl ow samplers that contain a fully electronic system built for 
a broad range of applications. Flow is compensated to within ± 5% accuracy over the full range of fl ows and back 
pressure.

There are three Universal XR pump models:

 

224-44XR  

 

No additional features

 

224-PCXR4  

 

LCD and 2-bu on keypad for built-in timer and fl ow fault/ba ery check

 

224-PCXR8  

 

LCD and 6-bu on keypad for programming delayed start time, automatic shutdown  

 

 

 

 

time, and intermi ent sampling plus fl ow fault/ba ery check

Models 44XR, PCXR4, and PCXR8 are RFI/EMI-shielded and UL Listed for intrinsic safety.

Performance Profi le

Operating Range:

1000 to 5000 ml/min (5 to 500 ml/min requires adjustable low fl ow holder)

Weight: 

34 oz (964 gm)

Dimensions:

5.1  x  4.7  x  1.9 inches;  (13 x 11.9 x 4.8 cm)

Compensation 
Range:

1000 ml/min up to 40 inches water back pressure
2000 ml/min up to 40 inches water back pressure
2500 ml/min up to 40 inches water back pressure
3000 ml/min up to 35 inches water back pressure
4000 ml/min up to 20 inches water back pressure
5000 ml/min up to 10 inches water back pressure

Flow Control: 

Holds constant fl ow to ± 5% of the set point

Run Time:

8 hrs minimum at 4000 ml/min and 20 in water back pressure, dependent on media used

Flow Indicator:

Built-in rotameter with 250 ml division; scale marked at 1, 2, 3, 4, and 5 L/min

Power Supply:

Charging Time:

(with SKC approved charger)

Plug-in ba ery pack, rechargeable NiCad 2.0-Ah capacity, 6.0 V, UL Listed

6 to 8.5 hrs with PowerFlex Charger

Operating Temp:

32 to 113 F (0 to 45 C)

Storage Temp:

-40 to 113 F (-40 to 45 C)

Charging Temp:

50 to 113 F (10 to 45 C)

Operating Humidity:

0 to 95% non-condensing

Multiple Sampling:

Built-in constant pressure regulator allows user to take up to four simultaneous samples 
at diff erent fl ow rates up to 500 ml/min each using optional adjustable low fl ow holder.

RFI-shielding
Performance:

Complies with requirements of EN 55022, FCC Part 15 Class B, EN 50082-1; frequency 
range of the radiated susceptibility test was 27 MHz to 1000 MHz, CE marked.

Intrinsic Safety:

UL Listed for: Class I, Division 1 and 2, Groups A, B, C, D; Class II, Division 1 and 2, 
Groups E, F, G; and Class III, Temp Code T3C.

 

Содержание 224-44XR































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды