manualshive.com logo in svg

SKC 224-44XR, Руководство по обслуживанию

Поделиться
Скачать
SKC 224-44XR Скачать руководство пользователя страница 19

Universal Pump Service Manual

15

15

15

15

15

Troubleshooting

•  Use a known good control board, stack, and motor when troubleshooting. SKC also recommends that a power supply be 

used for all testing. Connect it directly to the ba ery connector on the control board a er removing the ba ery pack.

Use only SKC-approved parts to ensure reliable performance. Failure to do so voids UL Listing for 
intrinsic safety and any warranty.

Failure to follow warnings and cautions voids any warranty.

Pump

Problem

Possible Solution

224-PCXR4 and PCXR8

Pump LCD doesn’t 
light when pump is 
turned on and the 
motor will not run.

•  Check that motor wiring is undamaged and solder joints at the 

motor and on the board are in good repair.

•  Check the battery for charge and proper voltage.
•  Swap with a known good battery for further troubleshooting.

224-PCXR4 and PCXR8

Pump LCD lights 
when pump is 
turned on, but the 
motor will not run.

Turn the fl ow adjust pot clockwise a few turns. The pot may have 
been adjusted to the lowest setting.
•  If the motor still does not respond, follow steps above. 
•  If the motor runs at full speed, turn the fl ow adjust pot 

counterclockwise. 

•  If the pot cannot be adjusted clockwise, it may have separated 

from the control board. Check control board. If pot has 
separated, resolder pot and test operation (

see Functional 

Testing, Flow Rate Spot Check

). If pot doesn't operate properly, 

replace the control board (Cat. Nos. P22433U [PCXR8] or 
P22433T [PCXR4]).

224-PCXR4 and PCXR8

Pump runs when 
turned on, but the 
LCD will not light.

Check the battery voltage or switch to an alternate power supply 
to check the LCD. If it still doesn’t light, it is either a bad LCD 
display or a bad diode on the control board. Replace LCD (Cat. 
No. P72380, 

see Pump Disassembly and Pump Reassembly

) 

or replace the control board (Cat. Nos. P22433U [PCXR8] or 
P22433T [PCXR4]).

Содержание 224-44XR































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды