background image

skcinc.com 

Form 37171 Rev 200630 

Page 33 

ACCESSORIES/REPLACEMENT PARTS 

 

Accessories

 

 

 

 

 

 

 

 

 

 

Cat. No. 

 

Standard Charging Cradle

, requires power supply see below 

220-800 

Single Cradle Power Supply

, for use with one charging cradle, 100-240 V 

 

220-600 

Multi Cradle Power Supply

, for use with 2 to 4 charging cradles, 100-240 V 

 

220-700 

Low Flow (5 to 500 ml/min) Kit

 includes All-in-One adjustable tube holder  

and Type A protective tube cover 

210-500 

Constant Pressure Controller

 for multiple-tube sampling 

 

 

 

224-26-CPC 

Protective Pouch

, nylon, with adjustable waist belt and shoulder strap, black 

224-911 

DataTrac Pro for Bluetooth-connected Pumps USB Bluetooth Adapter,  
required for free software download and use of DataTrac Pro software

 

877-94 

chek-mate Calibrator

, 0.50 to 5 L/min, includes 9-volt battery, and NIST-traceable 

calibration certificate 

375-0550N 

 

Replacement Parts

 

 

 

 

 

 

 

 

 

Cat. No. 

Replacement Battery Pack, Li-Ion

P75718 

Belt Clip

 

P51824 

Inlet

 

P20423 

Inlet Filter/O-rings

, pk/3 

P4001 

Screen Cover

 

P20422 

 

Use only SKC-approved parts to ensure reliable performance and to maintain the UL Listing 

for intrinsic safety. Failure to do so voids any warranty. 

Use of a repaired or rebuilt battery pack VOIDS ANY WARRANTY. 

 
SKC Limited Warranty and Return Policy 

SKC products  are subject  to the SKC Limited Warranty and  Return  Policy, which provides  SKC’s sole 
liability and the buyer’s exclusive remedy. To view the complete SKC Limited Warranty and Return Policy, 
go to http://www.skcinc.com/warranty.

 

 

*

Li-Ion Battery Testing and Shipment 

Rechargeable lithium-ion (Li-Ion) batteries for use with SKC sample pumps have been tested in accordance with the UN Manual and are proven to 
meet requirements of each test in the 

UN Manual of Tests and Criteria

, Part III, subsection 38.3. The batteries are rated below 100 watt-hours 

(Wh). 

AirChek Connect pumps contain Li-Ion batteries and are subject to special shipping regulations. Consult with your carrier for more information on 
Lithium Battery Shipping Regulations UN 3480 and UN 3481 or visit SKC’s website for more information at 
skcinc.com/catalog/pdf/instructions/1921.pdf 

 

Содержание 220-4000



































Отзывы: