SKC 220-4000 Скачать руководство пользователя | Manualshive

Страница: 30 / 34

background image

skcinc.com

Form 37171 Rev 200630

Page 30

2. An exclamation point icon appears on the display next to the flow rate

(

see right

).

3. After 20 seconds in fault, the pump will attempt to restart up to 5 times.

a. If full airflow is restored during the restart attempts, the pump will

continue the sample run.

b. If full airflow is

not

restored during 5 restart attempts within 5

minutes, the pump will end the sample run and display the
Sample Summary. The Sample Summary will indicate the
number of faults (

see right

). The LEDs will flash red with

decreasing frequency.

4. To clear a flow fault, touch any button on the display.

Note: A flow fault

will also be cleared when the battery charge is depleted.

Viewing History (History Menu)

Review specific sample run summaries directly on the pump screen as follows:

From Main Menu:

Using Pump with DataTrac Pro for Bluetooth-connected Pumps Software

AirChek Connect communicates with a laptop/PC via USB Bluetooth adapter Cat. No. 877-94 and
DataTrac Pro for Bluetooth-connected Pumps Software, which is available as a download (requires
Internet connection). Access Data for Bluetooth-connected Pumps Software as follows:

1. Check that the PC meets DataTrac Pro system requirements.
2.

Install the USB Bluetooth Adapter or “dongle” on laptop/PC according to the instructions included
with the adapter.

3. Browse URL provided in adapter instructions and download and install the DataTrac Pro Installer

on the laptop/PC. (A flash drive option is available for users without an Internet connection.)

4. Upon successful installation, DataTrac Pro will launch automatically and attempt to find any active

AirChek Connect pumps within the area.

For further instructions, see the DataTrac Pro for Bluetooth-connected Pumps User Manual.

Note

: The last 16 sample runs can be viewed as Sample Summaries on the pump. A maximum of 4416 data

entries can be held in pump memory. This equals approximately 70 hours of one-minute averages or 360 hours
of 5-minute averages. To access this data, upload it to DataTrac Pro for Bluetooth-connected Pumps Software
on your PC.

>Touch arrows to scroll
>Touch check mark to
select

>Touch arrows
to scroll selected
summary info

>Touch History

Touch Device

«
...
28
29
30
31
32
...
»

Содержание 220-4000



































Отзывы:

Нет отзывов

Похожие инструкции для 220-4000

Бренд: YGHP Страницы: 14

Бренд: IBC Страницы: 22

Бренд: Gardena Страницы: 16

Бренд: Envision Страницы: 36

Бренд: CLIVET Страницы: 7

PERFECT 350 ELECTRONIC

Бренд: Wijas Страницы: 9

Бренд: German pool Страницы: 11

Fre-Heater D Series

Бренд: Mueller Страницы: 34

Бренд: Geotech Страницы: 32

HydroTap All-In-One BC 60/85A

Бренд: Zip Страницы: 24

Бренд: Calpeda Страницы: 5

Бренд: Rheem Страницы: 47

Copper Cricket 1B

Бренд: Sage Advance Corp Страницы: 67

XCT 7 40VC009-048F-7G-QEE

Бренд: Carrier Страницы: 28

JUNG PUMPEN SIMER 4

Бренд: Pentair Страницы: 10

Бренд: VAKI Страницы: 9

Бренд: Textron Страницы: 20

Бренд: Pentair Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды