manualshive.com logo in svg

SKC 220-4000, Руководство по эксплуатации

Поделиться
Скачать
SKC 220-4000 Скачать руководство пользователя страница 31

skcinc.com 

Form 37171 Rev 200630 

Page 31 

MAINTENANCE 
 

Replacing the Battery Pack 
 

Ensure that pump is turned off before removing the battery pack and that no tubing or media 

are attached to the pump. 

1.  Turn the pump off by pressing the on/off button. 
2.  Remove the existing battery pack. 

a.  Use a 2.5-mm hex driver (Allen wrench) to loosen two screws on the bottom of the 

battery pack housing. 

b.  Pull the battery pack housing away from the pump case. 
c.  If replacing the battery pack with a new Cat. No. P75718, dispose of the used battery 

promptly. 

Do not disassemble the battery pack. Do not dispose of in fire. Dispose of used batteries 
promptly according to all state and local recycling of waste regulations.

 

3.  Install a new battery pack or reinstall the existing battery pack.

 

a.  Align the battery pack with the bottom of the pump case. 

Note: The connector on top of 

the battery pack should align with the protruding power control board contacts on the 
bottom of the pump case

.

 

b.  Press the two parts together until snug. 

Note: When the battery pack is attached, the 

pump screen will display a 20-second countdown as the zero setting of the flow sensor is 
performed.

 

c.  Use a 2.5-mm hex driver (Allen wrench) to tighten two screws on the bottom of the 

battery pack housing. Tighten the screws in an alternating fashion. 

d.  Charge the new battery pack completely before use; if reinstalling the existing battery 

pack, ensure that it is charged to at least 25% (battery status icon upon startup shows 
two bars). 

See Charging the Battery Pack

. 

Replacing the Screen Cover 

1.  Remove the two screws from the top of the screen cover mounting block. 
2.  Lift off the screen cover and mounting block. 
3.  Align and press-fit the mounting block onto the new screen cover posts (i.e., with the underside of 

the mounting block facing up and its straight edge facing away from the cover). Rotate the 
mounting block away from the screen cover until it is stopped by the inside edge of the screen 
cover. 

4.  Align the screen cover/mounting block with the holes in the top of the belt clip/top pump case. 
5.  Gently insert the two screws through the mounting block into the belt clip. Tighten until snug. 
6.  Ensure that the screen cover closes properly. 

Replacing the Belt Clip 

1.  Remove the screen cover.

 

a.  Remove the two screws from the top of the screen mounting block. 
b.  Lift off the screen cover and mounting block. 

Note: Do not remove the two lower hex nuts 

from the main case.

 

2.  Remove the screw from the bottom of the belt clip and pull the screw through the opening in the 

clip. 

3.  Lift the belt clip away from the pump. Ensure that the hex nut in the top of the case does not fall 

out. 

4.  Push the new belt clip into place until it fits snugly. 

Содержание 220-4000



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды