sitrex SB150 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

background image

ASSEMBLY, USE AND MAINTENANCE

16

LUBRIFICATION

The mower are delivered already

lubricated.

Grease all parts at least every 8 working
hours, especially the central (Rif. M). In
order to avoid excessive wear it is
indispensable to wash the bar with water at
the end of any mowing.

DRIVELINE

Grease Fitting are located on the Cross Assembly of each U Joint and on the Telescoping Tubes.
Do not force grease through the Needle Cup Assemblies.

Use quality grease to lubricate each part after the number of hours shown in the chart. Consult
the shaft operation and maintenance manual.

«
...
16
17
18
19
20
...
»

Содержание SB150





































Отзывы:

Нет отзывов

Похожие инструкции для SB150

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Бренд: Twiflex Страницы: 5

Бренд: Tripp Lite Страницы: 24

Бренд: JTECH Medical Страницы: 8

Бренд: Synthetic Sound Labs Страницы: 12

Бренд: Skytrofa Страницы: 35

Бренд: Hammer Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды