sitrex SB150 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

background image

ASSEMBLY, USE AND MAINTENANCE

15

HYDRAULIC SYSTEM

(OPTIONAL)

All the mowers can be provided with an hydraulic lifting device.

This accessory could only be

purchased by direct request.

It use exclusively to lift the cutter-bar in a

vertical position for

transporting.

Operate by means of a single acting

cylinder.

ASSEMBLY

Insert the support in the arm and fix it through the two
bolts M12 "A". Than secure the cylinder end point with
the apposite piston pin "F".

Assemble the second support with unit through the two
bolts M12 "A" to insert the piston rod in the pin and to
secure it through the apposite pin.

Connect the flexible tube end-point to the cylinder "B"
and connect the other end-point the hydraulic device of
the tractor.

USE

1) To stop the power take-off of the tractor.

2) To lift the mower through the lifting device of the tractor.

3) To operate the cylinder for the total lifting of the bar.

«
...
15
16
17
18
19
...
»

Содержание SB150





































Отзывы:

Нет отзывов

Похожие инструкции для SB150

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: A.MENARINI Страницы: 2

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Xo Страницы: 59

Бренд: Falcon Страницы: 8

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: PASCO Страницы: 30

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: TC Electronic Страницы: 14

Бренд: Access Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды