background image

 

 

   

 

 

             

Document NO.: RD-529-39-001 

                                                                                                                        Version: A     

- 6 - 

 

 

 

 
 
 

 
 
 

 

 
 
 
 

 

Diagram 4 

 

 

 

 

 

 

 

 

 

 

 

  Diagram 5 

Installation: 

Fix  the  one  CR17450    batteries  to each battery box of the 

smoke alarm.

 

·

According to the   

“Wireless function description”

 

Section  to  operate  the  smoke  alarm.  Ensure  the  wireless 

function is ok.   

·

Then  press  the  bracket  on  the  installation  position,  mark 

installation hole of bracket with pencil. 

·

Bore  two  installation  hole  on  the  sign  with  electric  drill. 

Make  diameter  of  holes  is  5mm,  Strike  the  two  plastic 

plugs into holes with hammer. 

·

Attach  the  bracket  to  the  plastic  plugs  and  fix  tightly  the 

screws  (3*25mm)  into  the  plastic  plugs.  (refer  to 

Diagram 6).   

·

Fit  the  alarm  on  the  bracket  and  turn  the  alarm  body 

clockwise, until matching well on the bracket. 

·

Test smoke alarm using test button. The sound pattern is 3 

short and weak beeps, 1.5seconds pause, 3 short and week 

beeps, 4.5seconds pause, repeat it, If continue testing , the 

beeps  will  become  louder.  Then  repeat  it  until  release  the 

button. 

·

If no sound, it indicates a defective alarm, you can refer to 
“Trouble  shooting”  for  solution  or  return  to  your  retailer 

during warranty.     

·

If you have any questions on installation, you can contact 

your retailer.   

·

During  testing,  may  the  other  smoke  detector  will  alarm. 

Once  release  the  button,  others  will  stop  alarming  in  1 

minute.  In  such  a  way,  you  can  check  the  wireless 

function. 

WARNING:

   

To  prevent  injury,  this  unit must  be  securely  attached  to  the 

ceiling in accordance with the installation instructions. 

 

Содержание GS529








Отзывы: