background image

Auto Jet Instruction Manual

4

    19/04/2018  Rev:2.0.0 

CENTRAL VACUUM SYSTEMS

ByTecnoplus 

s.r.l.

GENERAL INFORMATION

1. USING THE MANUAL

The instruction manual is a document written by the manufacturer and is an integral part of the central 
vacuum unit. In the event that it is resold, given or rented to others, it must be handed to the new user 
or owner.
It is recommended to use it and store it carefully during its entire service life.
The main objective of this manual is to indicate the correct use of the equipment, so that the best per-
formance is obtained,  while keeping it in perfect working order and safe condition.
No part of this document may be reproduced, copied or disclosed by any means without the written 
permission of TECNOPLUS s.r.l. owner of the SISTEM AIR brand. The TECNOPLUS company s.r.l. 
reserves the right to make improvements or modifi cations to this manual and to this device at any time, 
without the obligation to give prior notice to third parties.

To obtain the best results, the use of original  SISTEM AIR consumables is recommended

The SISTEM AIR trademark mentioned in this manual is a registered trademark and belongs to to the

owner TECNOPLUS S.r.l.

Содержание AUTO Jet TURBIX

























Отзывы: