Sirocco 16" Скачать руководство пользователя страница 22

Страница: 22 / 24

IGNITION FUNCTIONAL CHECK 1

See NO SPARK chart.

Consult the User's section

in this manual and retry.

Check isolation tap

and gas meter and retry.

Correct and retry.

Ther is a blockage in the system.

Check the inlet test point, the mag valve seating,

and blow out any dirt from the tubes and pilot.

YES

Purge the gas supply and retry.

YES

Has the system

got any air in it?

YES

Is the gas pressure correct?

Is the gas supply

turned on to the appliance?

YES

Ensure the gap between electrode and pilot burner

is as Figure 19. If still not working

replace ignition lead and then peizo.

Yes

Will the pilot light

with a match?

Is the control being
operated correctly?

YES

SYSTEM OK

YES

Does the pilot light?

Operate the valve.

Is there a spark?

PILOT WILL NOT LIGHT

Ensure there is no debris around the pilot assembly, e.g. coal, soot, etc.

which could short the spark, clean the area. Check for fluff in the pilot

aeration hole (see Figure 19).

IGNITION FUNCTIONAL CHECK 2

Consult the User's section

in this manual and retry.

YES

Check for damaged or defective control

knob spindle or cam operation. Check for correct

location of peizo components. Correct and retry.

Is the valve being

operated correctly?

Reset the electrode

gap and retry.

Replace the combined tap and peizo.

YES

Replace the ODS pilot.

Remove the lead from electrode. Using insulated pliers

hold the tip 3.5mm from the pipework.

Is there a spark when the valve clicks?

YES

Correct and retry.

YES

Has ignition lead become

detatched or has

a poor connection?

YES

Is the gap between

electrode and tpilot burner

as shown in Figure 19?

Operate the valve to

light the pilot.

Does the valve click?

NO SPARK

Ensure there is no debris around the pilot assembly, e.g. coal, soot,

etc. which could short the spark, clean the area.

VI-06-09

Содержание 16"

























Результаты поиска

Содержание 16"

Отзывы:

Похожие инструкции для 16"

Бренды по названию

Популярные бренды

Sirocco 16", Руководство пользователя, по установке и обслуживанию

Результаты поиска

Содержание 16"

Отзывы:

Похожие инструкции для 16"

Бренды по названию

Популярные бренды