Sirius Satellite Radio SLT960, Инструкции по установке, использованию и обслуживанию

Страница: 21 / 30

16
The false ceiling (plasterboard) shall be over
the larger side of the hood, fig. 13.
Provide a structure which is suitable to
bear the weight of the false ceiling, in or-
der it does not weigh on the hood .
RECYCLING VERSION – INTERNAL MOTOR
(BUILT IN)
After installing the hood, as described in the
previous section, connect a pipe from the
motor to the room where the air is to be di-
scharged.
Perform the electric connection into the po-
wer supply metal box found inside the ap-
pliance.
Fit the charcoal filters ( to be purchased as
accessories ) as shown in Fig. 17.
Refit the grease filters and close the glass pa-
nels.
You can connect an air diffuser at the end of
the air exhaust pipe , as shown in figure 20,
making sure to keep a minimum distance of
1 mt. between the hood and the air- diffuser.
EXTRACTION VERSION – EXTERNAL MO-
TOR (BUILT IN)
Mark the hood fixing holes shown in fig. 3 on
the solid ceiling .
Drill the four holes by using an 8mm diame-
ter twist drill . Insert the wall plugs and the
threaded bars supplied in the holes made .
You can choose the side of the hood where
to fit the air-out let, by following these steps:
Open the glass panels, by following the in-
structions given in the OPERATION MODE
section, and remove the grease filters.
In order to fit the air out-let on the hood up-
per side , you need to open the hole in the
centre of the hood upper side (fig.7) and fit
the air-out-let flange, as shown in figure 8.
In order to fit the air out-let in either the
longer or the shorter side of the hood, you
need to:
Remove the 4 screws, as shown in figure 4.
Remove the lower metal sheet , as shown in
figure 5
In order to fit the air out-let in the hood shor-
ter side, you need to remove the steel plug
(fig.9), by unscrewing the four fixing screws,
and then connect the air out-let with its spe-
cific bracket, as shown in figure 14.
In order to fit the air out-let in the hood lon-
ger side , you need to open the hole found in
the centre of the hood longer side ( fig. 12 ) ,
then fit the air out-let flange with its specific
bracket, as shown in figure 15.
Bring the appliance close to the ceiling and
push the power cord and the motor cable
through the specific pass (fig.2).
Secure the hood to the ceiling , by tightening
the nuts supplied .
Perform the electric connection into the po-
wer supply metal box found inside the ap-
pliance and connect the remote motor cable
to its specific connector.
Connect the internal motor or the external
motor’s cable to the terminal board found in-
side the plastic box of the wiring . Make sure
to respect the colors of cables when perfor-
ming the electrical connection (fig.23).
Refit the grease filter and close the glass pa-
nels.
Connect the air exhaust pipe to the hood air
out-let flange .
If you choose to fit the air out-let in the
hood shorter side, you can make the pipe fi-
xing operation easier by removing the cover
shown in fig. 16
The use of charcoal filters is not necessary
in this case
The false ceiling (plasterboard) shall be over
the larger side of the hood, fig. 13.
Provide a structure which is suitable to
bear the weight of the false ceiling, in or-
der it does not weigh on the hood.
Installation of air outlet joint diameter
200mm.
(THIS ITEM IS SUPPLIED WITH POWERFUL
MOTORS ONLY)
In case of installation of the air outlet dia-
meter 200mm which is possible on the upper
side of this ceiling hood only, please follow
these instructions.
Make the opening for the air outlet diame-
ter 200mm on the upper side of the product
(this opening is already marked on the body
of the unit.