background image

In this warranty:
We means Simx;
You means the consumer of the Goods 

Supplier means the authorised distributor or retailer that sold you the Goods in New Zealand 
or Australia; and

Goods means the Simx product accompanied by this warranty and purchased in New Zealand 
or Australia.

The benefits provided to you under the following warranty are in addition to any other rights 
and remedies available to you under the law:

1.  If, during the time from the date of purchase (Warranty Period), there is a defect in the 

Goods due to improper workmanship or material, we will replace or repair the Goods 
without charge. Any replacement product is warranted only for the time remaining on the 
original Warranty Period.

2.  We are not obliged to replace or repair the Goods under clause 1 if the Goods have been 

improperly stored, installed, connected, used, operated, repaired, damaged, abused, 
tampered with, altered (without our written approval), or not maintained in accordance with 
our recommended installation, connection and operating instructions.

3.  The warranty provided under clause 1 is limited to replacement or repair of the Goods only, 

at our option. To the extent permitted by law, we exclude liability for:

 

a) consequential loss or any other loss or damage caused to property or persons 

 

arising from any cause whatsoever;

 

b) damage to consumable items such as lamps and starters; and

 

c) damage arising from normal wear and tear.

4.  In order to claim under this warranty you must, within the Warranty Period, return the Goods 

to the Supplier, together with the original proof of purchase including the details below:

 

Supplier Name   

_____________________________

 

Date Of Purchase  

_____________________________

 

Model Number   

_____________________________

 

Invoice/Receipt No.   _____________________________

5.  This warranty does not cover the cost of claiming under the warranty or transporting the 

Goods to and from the Supplier.

Our Goods come with guarantees that cannot be excluded under the Australian Consumer 
Law. You are entitled to a replacement or refund for a major failure and for compensation for 
any other reasonably foreseeable loss or damage. You are also entitled to have the Goods 
repaired or replaced if the Goods fail to be of acceptable quality and the failure does not 
amount to a major failure.

SIMX WARRANTY INFORMATION 

LHT0090&91 251012:newnlht009091.qxd  10/26/12  5:17 PM  Page 3

Содержание LHT0090













Отзывы: