background image

4

www.simplicitymfg.com

BEFORE OPERATION

Clear the lawn of all sticks, stones, wire and other debris 
which may be caught or thrown by the mower blades.

Check grass condition. If wet, wait until later in the day. 
If grass is wet, the grass catcher is likely to become 
plugged.

For efficient bagging, air circulation under the 
mower deck, through the chute and into the bag is 
very important. 

For this reason, BEFORE YOU BEGIN MOWING you 
should make certain the underside of the mower and 
the underside of the catcher lid are free from grass and 
debris.

Make sure that there is a snug fit between mower 

deck, blower housing, tubes, and grass catcher cover.

MOWING WITH THE DOUBLE / 
TRIPLE CATCHER

Always operate with throttle at full speed when 
mowing.

Always wear hearing protection when operating 
grass catcher.

Grass should be cut often, and not too short. If grass 
is too long or lush it may be necessary to keep 
ground speed to a minimum or to cut only half the 
width of the mower to prevent clogging.  If grass is 
long, operate with mower in high cutting position 
for first pass, cutting again in a lower position on a 
second pass.

Do not open the cover with mower engaged.

If a large amount of cut grass is spilling out from 
under deck, the tube may be plugged or the bags 
may be full.  Discontinue mowing, stop the rider, 
disengage the PTO and then empty the catcher or 
clear the tube.

CAUTION

This machine produces sound levels 
in excess of 85 dBA at the operator’s 
ear and can cause hearing loss though 
extended periods of exposure.

Wear hearing protection when operating this 
machine.

General Operating Instructions

WARNING

ALWAYS shut off the tractor.  Disengage 
the PTO, and allow all moving parts to stop 
BEFORE disconnecting or clearing tube, or 
emptying catcher.

Before leaving the operator’s position for any 
reason, engage the parking brake, disengage 
the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider 
and mower free of grass, leaves and excess 
grease. Do not stop or park rider over dry 
leaves, grass or combustible materials.

Not 

for  

Reproduction

Содержание 5600352





















Отзывы: