background image

4190-9013 Remote Printer 

Installation Instructions

 

 

ã

 2000 Simplex Time Recorder Co., Westminster, MA 01441-0001 USA  

All specifications and other information shown were current as of publication, and are subject to change without notice. 

 

579-233

Rev. A

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS 
DAMAGED.

  Upon unpacking your Simplex product, inspect the contents of the 

carton for shipping damage.  If damage is apparent, immediately file a claim 
with the carrier and notify Simplex.   
 

ELECTRICAL HAZARD -

 Disconnect electrical power when making any 

internal adjustments or repairs.  Servicing should be performed by qualified 
Simplex Representatives. 

 

STATIC HAZARD

 -

 Static electricity can damage components.  Therefore, 

handle as follows: 
1.   Ground yourself before opening or installing components (use the 553-484 

Static Control Kit). 

2.   Keep uninstalled component wrapped in anti-static material at all times. 

 

RADIO FREQUENCY ENERGY -

 This equipment has been tested and found 

to comply with the limits for a Class B digital device, pursuant to Part 15 of the 
FCC rules.  These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial 
environment.  This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, 
may cause harmful interference to radio communications.  Operation of this 
equipment in a residential area may cause interference in which case the user 
will be required to correct the interference at his own expense. 

This document describes the installation procedure for the 4190-9013 Remote 
Printer.  Consult the 

User’s Guide

 supplied with your printer for a detailed 

description of mechanical setup, features and operating principles. 

The 4190-9013 Remote Printer interfaces with Simplex Fire Alarm and Nurse 
Call systems.  The printer provides hard copy of status reports for these systems: 

• 

Fire Alarm 

- 2120 

Multiplex 

  - 4120 

Network 

- 4010     - 4120 

GCC 

- 4020     - 4120 

NPU 

 

- 4100+ 

• 

5001 Nurse Call 

The following topics are covered in this publication. 

Topic 

Page Number 

Your Printer’s Default Settings 

Serial Interface DIP Switches 

Printer Connections 

Connecting to Fire Alarm Systems 

4010 Front Panel Programming for an RS-232 Port 

10 

Connecting to 5001 Nurse Call 

13 

Control Panel Buttons and Lights 

14 

Cautions and Warnings 

Overview 

In This Publication 

 

firealarmresources.com

Содержание 4190-9013

















Отзывы: