Simex SRP-147 страница 18 Скачать руководство пользователя

Страница: 18 / 64

User manual - METER SRP-147

4.4.

MAINTENANCE

The unit does not have any internal replaceable or adjustable components available to

the user. Pay attention to the ambient temperature in the room where the unit is operating.

Excessively high temperatures cause faster ageing of the internal components and shorten the

fault-free time of the unit's operation.

In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with

small amount of detergent or in the case of more significant contamination ethyl or isopropyl

alcohol.

Using any other agents can cause permanent damage to the housing.

Product marked with this symbol should not be placed in municipal waste. Please

check local regulations for disposal of electronic products.

FRONT PANEL DESCRIPTION

Symbols and functions of push-buttons:

Symbol used in the manual:

[ESC/MENU]

Functions:

•

Enter to main menu ( press and hold by at least 2 sec.)

•

Exit the current level and Enter to previous menu (or measure mode)

•

Cancel the changes made in parameter being edited

Symbol used in the manual:

[ENTER]

Functions

•

Start to edit the parameter

•

Enter to the sub-menu,

•

Confirmation of changes made in parameter being edited

Symbol used in the manual:

[^] [v]

Functions

• Change of the present menu,

• Modification of the parameter value,

• Change of the display mode.

MENU

ESC

ENTER

display

Thresholds exceeding

LED indicators (

)

alarm LED indicator (

)

programming
pushbuttons

MENU

ESC

ENTER

R2 R3 R4

Содержание SRP-147

































































Результаты поиска

Содержание SRP-147

Отзывы:

Похожие инструкции для SRP-147

Бренды по названию

Популярные бренды

Simex SRP-147, Руководство пользователя

Результаты поиска

Содержание SRP-147

Отзывы:

Похожие инструкции для SRP-147

Бренды по названию

Популярные бренды