Simex SRP-147, Руководство пользователя

Страница: 52 / 64

User manual - METER SRP-147
Register Write Range Register description
13h Yes 0 ÷ 3
“ Pnt ”parameter in “ InPt ” menu (the copy of 03h register, decimal
point position) 0 - “ 0 ”; 1 - “ 0.0 ”; 2 - “ 0.00 ”; 3 - “ 0.000 ”
14h Yes -999 ÷ 9999 “
Lo C ” parameter in “ InPt ” menu, no decimal point included
15h Yes -999 ÷ 9999 “ Hi C ” parameter in “ InPt ” menu, no decimal point included
16h Yes 0 ÷ 999 “ Lo r ” parameter in “ InPt ” menu, in 0.1%
17h Yes 0 ÷ 199
“ Hi r ” parameter in “ InPt ” menu, in 0.1%
18h Yes 0 ÷ 9999 “ t h1 ” parameter in “ InPt ” menu, no decimal point included
19h Yes 0 ÷ 9999 “ t h2 ” parameter in “ InPt ” menu, no decimal point included
1Ah Yes 0 ÷ 9999 “ t h3 ” parameter in “ InPt ” menu, no decimal point included
1Bh Yes 0 ÷ 9999 “ t d ” parameter in “ InPt ” menu, no decimal point included
1Ch Yes 0 ÷ 9999
“
t Sn
” parameter in “
InPt
” menu, no decimal point included
1Dh Yes 0 ÷ 9999 “ t Sh ” parameter in “ InPt ” menu, no decimal point included
20h 2 Yes 0 ÷ 199 Device address
21h No 20F5h Device identification code (ID)
22h 3 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h 4 Yes 0 ÷ 1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
24h Yes see descr.
Parameters of “
SECU
” menu (binary format (0 - „
oFF
”, 1 - „
on
”):
bit 0 - “ A r1 ” parameter; bit 1 - “ A r2 ” parameter
bit 2
- “
A r3
” parameter;
bit 3
- “
A r4
” parameter
25h Yes 0 ÷ 5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtO” parameter in “rS” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
28h Yes 0 ÷ 1
“ AL ” parameter in “ bEEP ” menu: 0 - off; 1 - on
29h Yes 0 ÷ 1 “ R1 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Ah Yes 0 ÷ 1 “ R2 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Bh Yes 0 ÷ 1 “ R3 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Ch Yes 0 ÷ 1 “ R4 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Dh Yes 1 ÷ 8
“
bri
” parameter (display brightness);
1
- the lowest brightness;
8
- the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
30h Yes -999 ÷ 9999 “ SEtP ” parameter in “ rEL1 ” menu, no decimal point included
52