Simex Simpact SLIK-73, Руководство пользователя

Страница: 36 / 44

User manual for universal counter with batching function SLIK-73
Register Write Range Register description
1Ah 6 Yes see descr. “oFFSEt” parameter in “PrESCA” menu (high word)
1Bh 6 Yes see descr.
“oFFSEt”
parameter in
“PrESCA”
menu (low word)
Cumulative value of registers 1Ah and 1Bh: from -99999 to 999999
1Ch Yes 0÷5
“ Point ” parameter in “ Presca ” menu (decimal point position)
0
- “
0
”;
1
- “
0.0
”;
2
- “
0.00
”;
3
- “
0.000
”;
4
- “
0.0000
”;
5
- “
0.00000
”
20h 3 Yes 0 ÷ 199 Device address
21h No 20C4h Device identification code (ID)
22h 4 Yes 0 ÷ 7
“bAud”
parameter in
“rS-485”
menu (baud rate);
0
- 1200 baud;
1
- 2400 baud;
2
- 4800 baud;
3
- 9600 baud;
4
- 19200 baud;
5
- 38400 baud;
6
- 57600 baud;
7
- 115200 baud
23h 5 Yes 0 ÷ 1
“mbAccE” parameter in “rS-485” menu (permission to write registers
via RS-485 interface); 0 - write denied ; 1 - write allowed
24h Yes see descr.
Parameters of “ SECU ” menu (binary format (0 - „ oFF ”, 1 - „ on ”):
bit 0 - “ A rEL ” parameter;
bit 4 - “ A oFFS ” parameter
25h Yes 0 ÷ 5
“rESP” parameter in “rS-485” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtimE” parameter in “rS-485” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
2Dh Yes 1 ÷ 8
“ briGHt ” parameter (display brightness);
1
- the lowest brightness;
8
- the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
30h 6 Yes see descr. “SEtP” parameter in “rELAy” menu (high word).
31h 6 Yes see descr.
“SEtP”
parameter in
“rELAy”
menu (low word).
Cumulative value of registers 30h and 31h: from -99999 to 999999
32h Yes 0÷3
“ modE ” parameter in “ rELAy ” menu:
0
- “
noAct
” mode;
1
- “
on
” mode;
2
- “
oFF
” mode;
3
- “
modbuS
” mode
33h Yes 0÷999
“timE” parameter in “rELAy” menu ( the time period of the relay
active state ), expressed in tenth of seconds or tenth of minutes
(depending on “unit” parameter);
34h Yes 0 ÷ 1
“unit” parameter in “rELAy” menu:
0 - “ SEC ” option; 1 - “ min ” option
1 - if overflow or underflow occurs (
“-Hi-”
or
“-Lo-”
), read of registers 01h and 02h (single registers) it returns
recalculated number of pulses ( while the overload of display quantity is very big this value can be erroneous).
Register 03h returns according error code.
2 - Preset of 0000h to these registers ( 04h, 05h, 06h and 07h, ) causes by zeroing of main counter and precounter
content
3 - after writing to register no 20h the device responds with an “old” address in the message.
4 - after writing to register no 22h the device responds with the new baud rate.
5 - the value of the “ mbAccE ” parameter is also connected to write to this register, so it is possible to block a writes,
but impossible to unblock writes via RS-485 interface, The unblocking of the writes is possible from menu level only.
6 - n umbers written to holding registers of relays thresholds are interrelated with each other auto-correction.
36