Sime RS 10 Скачать руководство пользователя страница 10

56

This occurs when the position of live
and neutral has not been respected
on  the  terminal  block.  There  is  a
break  in  the  wire  of  the  sensing
electrode  or  the  electrode  itself  is
earthed:  the  electrode  is  worn  out
and needs replacing.

NOTE: 
Should  the  equipment  “lock  out”,
first  wait  at  least  20  seconds  from
when  the  warning  lamp  lights  up,
before  pressing  the  push-button
with  built-in  light;  otherwise,  the
appliance will not be deblocked.

3.1.2

Ionization circuit

The  ionization  circuit  is  to  be  checked
using  a  dial-type  micro-ammeter,  or
preferably  a  digital  micro-ammeter
with a 0 to 50 µA scale. 
The micro-ammeter terminals must be
series-connected  to  the  wire  of  the
sensing electrode. 
Under  normal  operating  conditions,
the value oscillates between 6÷12 µA. 
The  minimum  value  of  the  ionization
current  for  which  the  equipment  can
“lock out” is about 1 µA. 
In this case, make sure that there is a
good  electrical  contact  and  check  the
degree of wear of the end part of the
electrode and the corresponding cera-
mic protection.

3.2

REGULATION THERMOSTAT

“RS” 

boilers are equipped with a regu-

lating  thermostat  with  a  double  con-
tact  having  differentiated  setting.  This
makes it possible to obtain a reduction

of heat output before the burner goes
out  completely,  by  means  of  the  coil
assembly (fig. 20) installed on the gas
valve regulator. 
This  step-modulation  system  affords
the following advantages:
–higher overall boiler efficiency;
–cont ainment  wit hin  accep t able

values of the increase in temperatu-
re  that  takes  place  in  the  cast-iron
body  (heat  inertia)  when  the  burner
goes out.

3.3

LAYOUT WITH TWO 
OPPOSED BOILERS

Accessories  are  available  on  request
to permit an opposed layout of two boi-
lers  which  will  reduce  overall  dimen-
sions and facilitate connection with the
flue through a single flue gas duct (figu-
res 14 - 15).
Table  2 gives  the  dimensions  of  the
two boilers combined and the diameter
of the chimney. 

Fig. 14

TABLE 2

D (ø mm)

L (mm)

A (mm)

RS  6

400

2360

600

RS  7

400

2360

600

RS  8

400

2360

600

RS  9

400

2360

600

RS 10

450

2360

600

RS 11

450

2360

600

RS 12

500

2380

620

RS 13

500

2380

620

RS 14

500

2380

620

Connecting cover

Connecting panel

RS 6

6136208

6136251

RS  7

6136209

6136251

RS  8

6136210

6136251

RS  9

6136211

6136251

RS 10

6136212

6136252

RS 11

6136213

6136252

RS 12

6136205

RS 13

6136206

RS 14

6136207

Fig. 15

KEY
1 Connecting cover
2 Connecting panel

Содержание RS 10
















Отзывы: