background image

3

Ioncell

5201128 Rev. D

The ionizer can be powered by a universal input, low voltage power supply, or 

through a 24 VDC power bus in the host main circuit. Multiple Ioncells can be 

linked together from a single power supply, allowing up to 6 units to be daisy-

chained. 
Operation of the Ioncell is automatically regulated by built-in proprietary circuitry. 

A green light on the face of the ionizer indicates active condition. A red light 

will indicate if a fault condition has occurred. Mounting holes for the ionizer are 

provided within the integral base of the unit. 
The in-line Ioncell is equipped for use with pressurized CDA only (clean dry air). 

Ioncell emitter points are general purpose Tungsten.

3. SPECIFICATIONS 

Input Voltage

Power Supply: Universal, 100-240 VAC, 50/60 Hz (24 VDC, 1.6A output)
Ioncell: 24 VDC, 0.1A (0.17A with optional fan)

Output Voltage

±4500 VDC, 5µA, Steady State

Offset Voltage

±50V

Enclosure 

White Polycarbonate (UL 94V-0 flammability rating) 

Alarm Output

TTL level alarm output

Indicators

Green, POWER ON;  Red, FAULT

Mounting

Integral mounting flanges accept four (4) #4 or #6 [M3 or M4] screws (not supplied)

Emitter Pins

Four (4), Tungsten

Operating Temp 

32-122°F [0-50°C]; non-condensing

Dimensions

Standard:  1.25”H x 1.3”W x 4.5”L [32 x 33 x 115 mm]

In-Line:  2.5”H x 1.3”W x 4.5”L  [64 x 33 x 115 mm]

Weight 

5.2 oz [145g]

Gas Input

In-Line: 45 psi [3.1 bar] max; clean dry air only

Gas Flow

In-Line: 0.8 scfm @ 5 psi to 3.2 scfm @ 45 psi [23 l/m @ 0.34 bar to 92 l/m @ 3.1 bar]

Airflow

5 cfm [0.14 m3/min] with optional fan

Discharge Time

Standard Ioncell: <15 seconds @ 6” [150 mm] to CPM plate 1000-100V
Ioncell with optional fan: <10 seconds @ 12” [300 mm] to CPM plate
In-Line Ioncell with output tube: 1” [25 mm] to CPM plate, 1000-100V

Tube Length

30 psi [2.0 bar]

15 psi [1.0 bar]

5 psi [0.34 bar]

6” [150 mm]

0.5 sec

0.8 sec

1.4 sec

12” [300 mm]

0.8 sec

1.4 sec

2.2 sec

18” [460 mm]

1.0 sec

2.1 sec

3.5 sec

24” [610 mm

1.8 sec

3.2 sec

5.2 sec

36” [910 mm]

6.0 sec

6.8 sec

10 sec

48” [1220 mm]

9.5 sec

13 sec

22 sec

Содержание Ioncell













Отзывы: