background image

4

Ioncell

5201128 Rev. D

4. INSTALLATION 

CAUTION – Sharp Points

Risk of injury. Keep hands/fingers away.

ATTENTION – Points pointus

Risqué de blessure. Gardez les mains / doigts éloignés.

NOTE

 – Inspect shipping container and contents for visible damage.  

Report any damage directly to the carrier before attempting installation of 

unit. 

The Ioncell ionizer is designed for fixed position mounting onto a secure equipment 

frame or partition surface. The flanged base of the ionizer may be used as a template, 

or see Figure 2 for complete dimensional information. 
Prepare mounting surface with necessary mounting holes.  Secure with #4 or #6 [M3 

or M4] screw hardware as required.  Mounting hardware is not supplied with unit. 
Important mounting location requirement:  The center of ionizer’s emitter pin grid 

must have a minimum 3” spherical radius clearance to any adjacent equipment 

frame or wall surface.  A clear line of sight is recommended to the area requiring 

static neutralization for best ionizer performance. 

CAUTION

 – This product is intended to be supplied by a Listed AC 

Adapter or Power Unit marked “Class 2” or “LPS” and rated output 24 

VDC, 1.7A.

ATTENTION

 – Ce produit est destiné à être alimenté par un adaptateur 

de courant alternatif ou transformateur listé “ classe 2 “ ou “ LPS “ et avec 

une puissance nominale 24 VDC, 1.7A.

Optional fan assembly mounting and connections: Engage open end of fan assembly 

directly around emitter pin grid area of the ionizer, until it snaps into place.  Secure 

fan assembly by placing fan locking bracket over base of fan assembly and tightening 

set screws (do not over tighten).  Insert power lead connector of fan assembly into 

socket located in the top of ionizer enclosure.  The black wire, pin 1 in the connector 

must be positioned towards the outside of ionizer enclosure.  See Figure 2 for 

complete connection diagram.
After the ionizer mounting has been completed, connect power cable between 

ionizer and power supply. Secure power supply as necessary. Connect line cord from 

power supply to the main electric source. The green light on ionizer will indicate 

normal operation.

Содержание Ioncell













Отзывы: