13
ht5000HB - pro5dl
interlaced signal outputs it is good practice to compare the
quality of the pictures reproduced by the HT5000HB - PRO5DL in
the two cases: the de-interlacing performed by the HT5000HB
- PRO5DL is often more effective than that performed by the
sources themselves.
gRAPhiCS RgB / YP
R
P
B
This input should be connected to an RGB/YPrPb type video or
graphic signal using a cable with a DB15HD type connector. The
signal source device (typically a personal computer or game
console) must be able to provide separate H/V synchronisation
or composite H+V synchronisation.
DVi-D
This input permits you to make the best use of digital image
quality. If your source has a DVI-D output (with YPrPb or RGB sig-
nal), connect it to this input to get the most out of the HT5000HB
- PRO5DL system.
hDMi™
HDMI (High Definition Multimedia Interface) integrates an un-
compressed high definition video signal with a multi-channel
audio signal and allows exchange of control data between
the video source and the HT5000HB - PRO5DL.
The HDMI™ input allows connection to video sources that use
the HDCP (High-Bandwidth Digital Content Protection) protocol
to protect their contents.
Once the video source has been connected to the HDMI™
input, internal processing by the HT5000HB - PRO5DL separates
the video information from the audio information.
You can use a DVI-D > HDMI adapter cable to connect the
DVI-D signal from a source equipped with a DVI-D output.
SDi
The HDSDI/SDI input permits you to connect sources with serial
digital outputs in YPrPb components in compliance with the
SMPTE292M (high definition) and SMPTE259M-C (standard
definition) standards. The signal, of the uncompressed type, is
transmitted digitally by single coaxial cable, thus guaranteeing
a high level of resistance to noise and disturbance.
COMPOSiTE ViDEO
Fit an RCA connector with a Composite Video (CVBS) signal
to this input.
The output connector on the external appliance is normally
coloured yellow and will often be labelled VIDEO.
Other signal and socket formats may be preferable (because
they give better image quality), but this type of output socket is
still the most commonly used, and nearly all television receivers,
video recorders, DVD players and camcorders, etc. use it.
S-ViDEO
Fit a mini-DIN connector with an S-Video signal to this input.
The corresponding output on the external device is normally
identified by the labels S-VIDEO or Y/C. This type is nearly as
common as Composite Video, and is preferable to the latter,
since it gives higher image quality.
RgB/YP
r
P
b
These inputs use a set of 4 RCA (3) connectors and 5 BNC (4)
connectors. RGB and Component signals can be applied to
each set of connectors.
If you use the RGB inputs you can select YPrPb video mode.
The RGB signals may have composite synchronisation on the
green signal (RGsB), composite synchronisation on the HV sig-
nal and separate synchronisation on the H and V signals via
BNC connectors. Connect the R, G, B outputs of the source to
the respective R, G, B inputs of the HT5000HB - PRO5DL (tak-
ing care not to invert the positions) and any synchronisation
signals to the HV. With regard to the 3 sets of RCA connectors,
when hooking up, use the colours of the RCA connectors as
an aid as follows: the R connector is red, G is green, B is blue
and HV is white.
You can use a SCART to RCA adapter cable to connect the
RGB signal from a source equipped with a SCART output to
this input.
The Component signals connect to the Y, Pr and Pb inputs: take
care that the inputs match the outputs on the source device.
As indicated in the table, the colours of the connectors can
also be of help.
Only horizontal scanning frequencies of 15 kHz (standard
video resolution) or 32 kHz or higher (high definition video, with
progressive scanning, high definition video) can be applied
to this input.
Progressive signals usually provide better quality than interlaced
signals, but if the source features both progressive and de-
1
2
3 4
5 6
8 9
10
11
12 13
14
7
