![background image](http://html.mh-extra.com/html/silverline/251483/251483_manual_1273642008.webp)
8
GB
• Fitting waist belt (see Image G-H):
1. Stand upright and straight, locate both ends of the Waist Belt Strap (6) and
ensure they are not twisted
2. Fasten the Waist Belt Buckle (7), by inserting the three-bar slide through the
square link, so both parts sit flat on top of each other and interlock
3. Adjust the Waist Belt Strap by pulling the end of the webbing through the belt
slider, until a snug fit is achieved
Note:
Confirm comfortable yet snug fit of the harness by squatting down and
moving your arms above your head. The user must be able to comfortably
move around and reach his working position, without the harness restricting
movement.
Connecting to other fall arrest system components
WARNING:
Karabiners and other connectors must ALWAYS be used with
the gate closed and securely locked. Refer to the connector manufacturer’s
instructions for verification and inspection procedure.
WARNING:
The total length of a lanyard connected to an energy absorber
should NOT exceed 2m.
• Use the Dorsal Attachment Point (A) (10) to connect to the shock absorber or
shock absorber/lanyard combination using a suitable karabiner
• Use the Sternal Attachment Point (A/2) (5) to connect to a mobile fall arrester
and other rope access systems according to EN 363
Clearance
Fall clearance (Fig. II):
• Before use, it is essential to verify the clearance required beneath the user. This
clearance must be sufficient to prevent the user from hitting the ground or
another obstacle, in the event of a fall
Swing falls (Fig. III):
WARNING:
The force of striking an object in a swing fall may cause serious
injury or death.
• Swing falls occur when the anchorage is not located directly above the point
where a fall occurs.
• Minimise swing falls by working as close as possible to the anchorage
• DO NOT enter a situation where a swing fall could occur, if it is likely to result
in an injury
Note:
The risk of swing falls significantly increases the clearance required when
using a self-retracting lifeline or another variable length connecting system.
Connecting to work positioning or restraint systems
Note:
This harness is fitted with a Waist Belt Strap (6) and Lateral Attachment
Points (11) that enable its use in work positioning systems to provide support.
Use a back-up fall arrest system if working at height.
• The Lateral Attachment Points (11) are designed to either hold the user in a
certain position whilst working (work in suspension), or to prevent the worker
from entering a zone where a fall is possible (travel restraint, leash principle,
see Fig. IV)
• The Lateral Attachment Points must ONLY be used to attach to a work
positioning system. DO NOT connect to a fall arrest system
• ALWAYS use the two lateral D-rings together by clipping a suitable positioning
lanyard between them
• There should be a supporting surface for the feet for comfortable work
positioning
• Movement must be restricted to a maximum of 0.6m, and the lanyard must
be kept under constant tension (see Fig. V)
WARNING:
When connectors are poorly positioned, the attachment D-rings
could act as a lever on the gate of a karabiner and subsequently damage it when
sudden tension comes on to the rope. ALWAYS ensure connectors remain safely
positioned during use.
Anchorage requirements (Fig. VI)
• The minimum strength of any anchorage must be 10kN, according to EN795
• Check anchorage for signs of deterioration
• As with all fall arrest gear, anchorages must be subjected to regular
inspections by a competent person. Inspect at least once every three months
and record findings in a dedicated service record
• Check that the karabiner is the correct size for the anchorage to be used. If the
karabiner is too small, use an anchor sling to connect to the anchorage
Anchorage position
WARNING:
The anchorage for work positioning must be positioned at or
above waist level.
• The anchorage of the fall arrest system should preferably be located above
the user’s position
Use as part of a fall arrest system
• Anchorages selected for fall arrest systems should be capable of sustaining a
static load, applied in the directions permitted by the system of at least:
• 22kN for non-certified anchorages
• 2 x the maximum arrest force for certified anchorages
• If more than one system is attached to one anchorage, the required
strength should be multiplied by the number of systems attached
Compatibility
• This harness is compatible with miscellaneous fall arrest systems and safety
gear, including but not limited to the following Silverline products:
• Shock Absorbing Lanyard
• Karabiner
• Restraint Positioning Lanyard
Notes:
• Connecting hardware must be compatible in size, shape, and strength.
Non-compatible connectors may accidentally disengage and lead to serious
injury or even death
• Only use connectors, such as D-rings, snaphooks, karabiners and other
equipment with a minimum rating of 22kN
WARNING:
Always verify that all components used in combination with each
other are compatible.
Removing the harness
1. Ensure you are located in a safe place, away from any fall hazards
2. Open both Leg Strap Buckles (9) by passing the three bar slide through the
square link
3. Open the Chest Strap (2) buckle
4. Remove your arms from the harness
Note:
Inspect the harness after use, and follow instructions for cleaning,
disinfection, transport and storage as outlined in ‘Maintenance’.
Operation
Note:
This equipment must ONLY be used by competent operators. All users
must be trained in its safe use. Inexperienced users must receive instruction
prior to using this equipment. A risk assessment must be carried out before
undertaking any operations requiring fall arrest equipment.
WARNING:
ALWAYS wear personal protective equipment appropriate for the
work area and type of activity, including but not limited to, eye protection, gloves,
hard hat, protective shoes and hearing protection.
Note:
Check the correct fitting and adjustment at least every 2 hours during use.
This may save your life!
Regularly check connections with other equipment in
the system and ensure various system components are correctly positioned with
respect to each other.
251483_Manual.indd 8
10/12/2019 09:53