manualshive.com logo in svg

Silicon Laboratories ZigBee, Руководство пользователя

Поделиться
Скачать
Silicon Laboratories ZigBee Скачать руководство пользователя страница 6

4.3  ZigBee Smart Outlet Reference Design

This reference design contains many features for the evaluation of a smart outlet, including:

Table 4.2.  ZigBee Smart Outlet Reference Design Features

Reference Design Features

Benefit

15 A power relay

Allows for power control of most household electronic products.

Energy monitoring circuit

Provides power, voltage and current status of a device being powered by the refer-
ence design.

Temperature and relative humidity sensor

Provides room environmental sensing capability.

Ambient light sensor

Provides room lighting status information in proximity to the reference design.

Network status LED

Provides feedback on the RF network status.

Power status LED

Provides feedback on the power circuitry.

10-pin Mini Simplicity Connector

Facilitates ZigBee packet trace and debugging.

User button

Eases network commissioning (join/leave) and manual power override.

Test points

Simplifies hardware-level debugging.

4.4  Hardware Features

The smart outlet hardware reference design contains the following features:

• Silicon Labs EFR32MG1P232F256GM48 ZigBee Pro Radio:

• 32-bit ARM® Cortex -M4 with DSP and FPU
• 2.4-GHz IEEE 802.15.4-2003 transceiver & lower MAC.
• Hardware Cryptographic Acceleration for AES 128/256, SHA-1, SHA-2 (SHA-224 and SHA-256) and ECC.
• 256 kB user programmable flash with 64 kB RAM.
• Flexible ADC, UART/SPI/I2C serial communications, and general purpose timers.
• Highly efficient Thumb-2 instruction set.

• Silicon Labs Si7021 relative humidity and temperature sensor:

• Temperature sensor accuracy: ±0.4 °C
• Humidity sensor accuracy: ±3% RH
• I2C interface

• Silicon Labs Si1141 ambient light sensor:

• Ambient light sensor range: 1 to 128 kilo lux
• I2C interface

• Additional hardware features:

• Integrated PCB antenna.
• Energy monitoring device
• Full packet trace port for RF communications debugging.
• Pushbutton for manual on-off power and network join.
• Green Network/status LED.
• Red power status LED.
• Fully qualified BOM for 0 to 55 ºC operation.
• Pre-certified FCC Part 15.
• Pre-certified UL.

UG171: ZigBee

®

 Smart Outlet Reference Design (RD-0051-0201) Kit User's Guide

Overview

silabs.com

 | Smart. Connected. Energy-friendly.

Rev. 0.1  |  5

Содержание ZigBee






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды