Silex technology BR-310AC Скачать руководство пользователя страница 16

Страница: 16 / 108

BR-310AC User's Guide

2-2. Parts and Functions

The parts name and functions are as follows:

Front

(1) Push Switch

Start in Configuration
Mode

Press and hold this switch for 5 sec while BR-310AC is active.

Wireless configuration
using Smart Wireless Setup

Press and hold this switch for 10 sec while BR-310AC is active.

F a c t o r y d e f a u l t
configuration

Press and hold this switch while turning on BR-310AC and

release it when the WLAN LED turns from Green to Red.

(2) Status LED

(Green / Orange)

Blink (Orange) Waits for connection when the Link LED is turned off.

Handles data communication when the Link LED is turned on.

(3) LAN port

Connect a network cable.

(4) Link LED (Green)

Has connected to a wired LAN.

(5) AC connector

Connect an AC adaptor.

Содержание BR-310AC












































































































Результаты поиска

Содержание BR-310AC

Отзывы:

Похожие инструкции для BR-310AC

Бренды по названию

Популярные бренды

Silex technology BR-310AC, Руководство пользователя

Результаты поиска

Содержание BR-310AC

Отзывы:

Похожие инструкции для BR-310AC

Бренды по названию

Популярные бренды