manualshive.com logo in svg

SILENT KNIGHT 5104B, Инструкция по установке и эксплуатации

Поделиться
Скачать
SILENT KNIGHT 5104B Скачать руководство пользователя страница 14

Model 5104B Installation Manual

151053-L8

 3-6

3.4.2.3 Overcurrent LED Indicators (L1 & L2)

The 5104 has two red LEDs which indicate if excessive current is being drawn by a device connected to either 
the Accessory Power or Smoke Power circuits. Table 3-4 lists the two overcurrent LEDs and gives a description 
of them. See Figure 3-2 for LED locations.

If either L1 or L2 turn on disconnect power immediately. Refer to Section 8 for troubleshooting information.

3.4.3

Reset / Silence Switch

The Reset/Silence switch has three functions:

•

Silences audible trouble, or supervisory signals. A trouble or supervisory piezo annunciation will be silenced 
immediately when you press the switch.

Note:  If the switch is depressed for 15 seconds or longer an audible trouble signal will occur

•

Resets smoke detector power. This function removes power from terminals 6, 9 and 11.

Note: To reset smoke detector power, depress the reset /trouble switch for a minimum of 1 second.

•

Reset accessory powered devices. This function removes power from terminal 24.

Note: To reset accessory powered devices depress the reset/silence switch for a minimum of 1 second

The Reset/Silence switch is accessible inside the panel (DO NOT install the switch extender provided with the 
system) for UL certified installations.

3.4.4

Cable Connectors (P1, P2, and P3)

There are two connectors on the 5104 (see Figure 3-2 for P1 and P2 locations). The function of these connectors 
is as follows:

3.4.5

On-board Piezo Sounder

The on-board piezo sounder gives an audible output for trouble, and supervisory conditions. Troubles and 
supervisories can be silenced with the Reset/Silence switch immediately.

Table 3-4: Overcurrent LED Description

LED #

Name

Color

Description

L1

Accessory Power 

Fault

Red

If a device connected to the accessory power circuit draws 
more than 750 mA the overcurrent poly fuse will open and L1 
will turn on.

L2

Smoke Power Fault

Red

If a device connected to the smoke power circuit draws more 
than 750 mA the overcurrent poly fuse will open and L2 will 
turn on.

Connector

Function

P1

Connects the wires from the secondary winding of the AC transformer 
to the control panel. (See Section 8 

Troubleshooting

 for additional 

information. 

P2

Used as a quick-connect for the 5230 Remote Annunciator to do 
programming or troubleshooting. 

P3

Standby battery connector.

Содержание 5104B

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды