Silent Alert SA3000 Скачать руководство пользователя страница 2

Страница: 2 / 13

SILENT ALERT SA3000 FIRE SAFE MANUAL 24/04/2015

Designed & Manufactured by Clofield Limited

Free technical helpline 01246 450789 www.silent-alert.co.uk

TECHNICAL SPECIFICATION

Introduction

The Silent Alert Fire Safe system alerts people who are deaf when a fire alarm is activated; it
comprises a fire alarm interface and one or more compatible receivers. The fire alarm interface
links to a fire alarm panel via a volt free relay and incorporates a radio transmitter. When the fire
alarm is activated the transmitter within the fire alarm interface sends out a coded radio signal.
When a Pager receives this signal it vibrates and lights a fire key on the Pager display. The
system is designed to comply with all relevant parts of BS5839-1 2013 & EN54-2 and

MUST

installed by a competent person as defined in BS5839-1 2002.

Installation Training

Installation training is available; please call us on 01246-450789 for more details.

Fire Safe Interface Panel

Part Number:

FSTX-2225-EU

Dimensions:

H300mm x W210mm x D160mm

Weight:

Without Battery 1.50 KG - With battery 2.3KG

Material:

Polycarbonate self-extinguishing enclosure.

Protection:

Water resistant

Power Supply:

240v AC 50 Hz

Battery back up:

6volt lead acid 4Ah (Yuasa Type Y4-6) Dimensions

H100mmxW47mmxD70mm

Alarm Panel feed to Fire Safe Panel:

Normal condition 5-30 Volts DC.

Grounded in alarm mode via an integral OPTO isolated voltage fed relay.

Fault signal to Fire Panel:

Via an integral normally open or normally closed volt free relay.

Fault conditions:

Mains failure, battery removal or charge failure,
PCB failure, radio failure

Radio compliance:

In accordance with EN300 220-1.

Radio licence:

Licence exempt

Range:

Up to 1000m in open air

Pager Unit

Part number:

PG3A-2204-EU MKIII

Dimensions:

H63mm x W82mm x D26mm (Excluding belt clip)

Weight:

74gms

Material:

Impact resistant ABS

Power supply:

Integral NiMH 3.6Volt rechargeable battery pack.

Charger:

Intelligent boost, trickle and maintenance charging.

Fault conditions:

Low battery & radio failure.

Radio compliance:

In accordance with EN300 220-1.

Radio licence:

Licence exempt.

Range:

Up to 1000m in open air.

Other:

Integral field strength / data validation meter for system commissioning.

Содержание SA3000














Результаты поиска

Содержание SA3000

Отзывы:

Бренды по названию

Популярные бренды

Silent Alert SA3000, Техническое руководство

Результаты поиска

Содержание SA3000

Отзывы:

Бренды по названию

Популярные бренды