Silencer 65SL страница 4 Скачать руководство пользователя

Страница: 4 / 24

IM_FULL_65SL_REV-A

MAIN POWER CONNECTOR

5 PIN MAIN POWER WIRE HARNESS:

RED / WHITE WIRE –PARKING LIGHT RELAY INPUT —

The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE wire

will determine the output polarity of the flashing parking light relay.
If the vehicle you are working on has +12volt switched parking lights,

you don’t need connect this wire.

This wire is already connected to +12volt.
If the vehicle’s parking lights are ground switched, cut the RED/WHITE wire, connect the

RED/WHITE wire to chassis ground.

WHITE WIRE — PARKING LIGHT RELAY OUTPUT

(+12 V 10A OUTPUT) —

Connect the WHITE wire to the parking light wire coming from the headlight switch. Do not connect the WHITE wire to the

dashboard lighting dimmer switch.

(Damage to the dimmer will result).

The limitation of the WHITE wire is 10 AMP max.

Do not exceed this limit or damage to the alarm and parking relay will result.

BLACK WIRE — SYSTEM GROUND –

This is the main ground connection of the alarm module. Make this connection to a solid section of the vehicle frame. Do

not connect this wire to any existing ground wires supplied by the factory wire loom, make the connection to the vehicle’s

frame directly.

BROWN WIRE – (+) SIREN OUTPUT –

This wire is provides power to the supplied siren. Connect the Brown wire to the Red wire of the siren. Connect the Black

wire of the siren to a stable chassis ground.

RED WIRE — SYSTEM POWER (+12V CONSTANT) —

The RED wire supplies power to the system. Connect this wire to a stable co12 volt source.

4 PIN ANTENNA, LED AND VALET SWITCH CONNECTOR

The antenna should be mounted to the front windshield of the vehicle

facing down. It should be clear of any metallic objects or tinting and as

close to the center as possible. The Valet switch and LED are mounted

within this unit and are connected with the ribbon cable.

RED / WHITE: PARKING LIGHT RELAY INPUT
WHITE: PARKING LIGHT OUTPUT
BLACK : MAIN SYSTEMS GROUND
BROWN : POSITIVE SIREN OUTPUT
RED : FUSED 12 VOLT (+) BATTERY POWER

Содержание 65SL

























Результаты поиска

Содержание 65SL

Отзывы:

Похожие инструкции для 65SL

Бренды по названию

Популярные бренды

Silencer 65SL, Руководство по установке

Результаты поиска

Содержание 65SL

Отзывы:

Похожие инструкции для 65SL

Бренды по названию

Популярные бренды