Silencer 65SL страница 13 Скачать руководство пользователя

Страница: 13 / 24

IM_FULL_65SL_REV-A

FEATURE “A” PROGRAMMING

1. Turn the Ignition ‘switch

“ON/OFF” 3

times

and stay in the

“OFF”

position.

2. Push the Programming switch

3 times

(holding in on the 3rd push) until a

long chirp is heard,

then release the

Programming switch. You are now in the feature

“A”

programming mode.

3. Press and release the transmitter button with the Icon corresponding to the feature with the icon you want to program.

a. The (optional) horn chirps and the LED will flash then pause, indicating a previous setting.
b. The factory default settings are always [1] LED flash, [1] horn chirp.

4. Depress the transmitter button icon again to change the feature. Simply keep re-depressing the transmitter button icon

again until the module advances to your desired setting.

5. Depress the next desired transmitter icon button corresponding to the feature you want to program.

Press

Transmitter

Button

One Chirp /

LED One Pulse

Factory Default Setting

Two Chirps /
LED Two Pulses

Three Chirps /
LED Three Pulses

Four Chirps /
LED Four Pulses

Active Arming

Passive Arming

Without Passive

Door Locking

Passive Arming

With Passive Door

Locking

Lock/Arm & Unlock/Disarm

Confirmation Chirp

Lock/Arm

Confirmation Only

45 Second Delay Door Ajar

Error Chirp

Instant Door Ajar

Error Chirp

All Confirmation Chirps ON

Siren Confirmation

Chirp

Only

Horn Confirmation

Chirp

Only

All Confirmation

Chirps

OFF

5 +

Brown/White Wire =

Horn Output

Brown/White Wire =

Dome Light Output

Brown/White Wire

= Factory Security

Rearm Signal

(4 chirps) Brown/White

Wire = Channel # 4
1- Sec. Pulse O/P

(5 chirps) = Channel 4

Latched O/P

6 +

Automatic Rearm OFF

Automatic Rearm

7 +

Without Car-Jack Mode

Active Car-jack

Mode

Passive Car-jack

Mode

8 +

Dome Light Turns ON & OFF

After Ignition ON & OFF

(45 Second Door Bypass)

With Dome Light

Turns

after

ignition

OFF

(45 Second Door

Bypass)

Without this

Feature

Exit:

Turn Ignition to the

“ON”

position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.

Содержание 65SL

























Результаты поиска

Содержание 65SL

Отзывы:

Похожие инструкции для 65SL

Бренды по названию

Популярные бренды

Silencer 65SL, Руководство по установке

Результаты поиска

Содержание 65SL

Отзывы:

Похожие инструкции для 65SL

Бренды по названию

Популярные бренды