Silencer 65SL Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

Silencer 65SL Скачать руководство пользователя страница 17

IM_FULL_65SL_REV-A

17

START FEATURE “E” PROGRAMMING

Turn the Ignition ‘switch

‘ON/OFF’ 3 times

and stay in the

“OFF”

position.

Push the Valet switch

7 times

(holding in on the

7th push

) until one long chirp is heard and then release the valet switch.

You are now in the Start feature

“E”

programming mode.

Press and release the transmitter button corresponding to the feature you want to program.

Press

Transmitter

Button

One Chirp /

LED one pulse

Factory Default Setting

Two Chirps /
LED Two Pulse

Three Chirps /
LED Three Pulse

Four Chirps /
LED Four Pulse

1 +

Voltage Check Type (B)

Tachometer

Check Type (A) Timer Checking Type (B) Data Bus Interface Mode

**

2

A> RPM learning – see RPM Learning below.

B>

Start Crank Time:

0.6-second

0.8-Second (2 Chirps), 1.0-Second (3 Chirps), 1.2-Second (4 Chirps),

1.4-Second (5 Chirps), 1.6-Second (6 Chirps), 1.8-Second (7 Chirps),

2.0-Second (8 Chirps), 3.0-Second (9 Chirps), 4.0-Second (10 Chirps),

3

Start or Stop the System for TESTING & ADJUSTMENTS

4

Low check level

Hi Check Level

5 +

+ 50 RPM

DBI ONLY

No RPM

Learning

6 +

- 50 RPM

DBI ONLY

No RPM

Learning or

< 50 RPM

7

+

Automatic

Transmission

8

+

“TEST” Mode for Zone 2

/ Instant Trigger & Zone 3

/ Door Trigger

“TEST” Mode

for Zone 1

& Zone 4 (2

Stage Shock

Sensor)

Exit:

Press the button on the transmitter. 3 long chirps & 3 parking light flashes will confirm exit.

RPM LEARNING

Note:

To set RPM learning, the White/Red wire from the 16 pin connector must be connected properly.

1. Enter Start Feature “E” Program mode.
2. Press the + buttons together to set “Tachometer Checking Type” on (2-chirps).
3. Press the button to confirm RPM learning mode on (1-chirp).
4. Start the vehicle with the ignition key. While the engine is running the parking lights and LED will flash. If they flash,

proceed to point 5. If they do not flash, turn the ignition key to the

OFF

position and press the button to exit

“E”

programming mode. Check or re-connect the White/Red wire from the 16 pin connector and re-try.

5. Press and hold the valet button (2-3 sec) until a long chirp is heard and the LED stays on solid for 2 seconds.

The RPM signal learning is complete.

6. Stop the engine using the ignition key.

«
...
15
16
17
18
19
...
»

Содержание 65SL

























Отзывы:

Нет отзывов