Silca TARGA 2000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 26

background image

Operating manual - English

TARGA 2000

22

Copyright Silca 1999

7.4

Fuse replacement

ATTENTION: Unplug the machine from the mains.

1) Detach the wiring from the machine plug.
2) Turn the key-cutting machine to the right so that the fuse box is easily reached.
3) Remove the fuse box placed below the power inlet (Q) (fig. 22).
4) Replace the fuses (P).
5) Close the fuse box and connect the power cable.

ATTENTION: the fuses must be of the same type (rapid) and with the same amps (4A for the 230V

machine; 8A for the 110V machine).

Fig. 22

P

«
...
20
21
22
23
24
...
»

Содержание TARGA 2000



























Отзывы:

Нет отзывов

Похожие инструкции для TARGA 2000

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Eaton Страницы: 16

RMQ-Titan C22-PV Series

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 98

Бренд: Eaton Страницы: 15

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды