Silca TARGA 2000 Скачать руководство пользователя страница 25

Страница: 25 / 26

Silca S.p.A.
Vittorio Veneto

SILCA S.p.A.
Via Podgora, 20 (Z.I.)
31029 VITTORIO VENETO (TV)
Tel.: 0438 9136
Telefax: 0438 913800

P. IVA COD. FISC. E REG. IMPR. 03286730266

www.silca.it

REA TV 258111 - CAP. SOC. € 10.000.000 i.v. - EXPORT TV 038851

A Member of the Kaba Group

VITTORIO VENETO 11/11/2005

CE DECLARATION OF MACHINE COMPLIANCE

SILCA S.p.A. - VIA PODGORA 20 ( Z.I.)
31029 VITTORIO VENETO (TV) - (ITALY)
TEL. 0438 9136 - FAX. 0438 913800

Declares under its own responsibility that the

Key-cutting machine

model

TARGA 2000

complies with the requirements of the following European Directives:

European Union

DIRECTIVE 98/37/CEE

(Machines)

and with the EN 292/1 – EN 292/2 Standards

European Union

DIRECTIVE 89/336/CEE

(Electromagnetic Compatibility)

and with the EN 55022 / IEC 801 – 2 / IEC 801 – 4 Standards

European Union

DIRECTIVE 73/23/CEE

(Low Voltage)

| 97 |

and with the EN 60204-1 / EN 60950 Standards

General Manager Basic Production Center

Содержание TARGA 2000



























Результаты поиска

Содержание TARGA 2000

Отзывы:

Похожие инструкции для TARGA 2000

Бренды по названию

Популярные бренды

Silca TARGA 2000, Руководство по эксплуатации

Результаты поиска

Содержание TARGA 2000

Отзывы:

Похожие инструкции для TARGA 2000

Бренды по названию

Популярные бренды