background image

Page 2

Doc No. DCP0000487  JH  12/7/99  rev3

AC power operation

For normal AC operation, plug the AC power
supply cord in a wall outlet of 230 V specified
voltage. The unit complies with BS415.

AC power cord
The wires in the mains lead supplied with the
unit are coloured in accordance with the follow-
ing code.

Green and Yellow

Earth

Blue

Neutral

Brown

Live

As the colours of the wires in the mains lead of
this unit may not correspond with the coloured
markings identifying the terminals in your plug,
please connect as follows.

Wire

Plug terminal

Green & Yellow ‘E’ mark

‘EARTH’ symbol mark
‘GREEN’ mark
‘GREEN AND YELLOW’ mark

Blue

‘N’ mark
‘BLACK’ mark
‘BLUE’ mark

Brown

‘L’ mark
‘RED’ mark
‘BROWN’ mark

Caution
To prevent electric shock do not remove
the cover

Upon receipt of the amplifier shipment, please
inspect for any damage incurred in transit. If
damage is found, please notify your local repre-
sentative and the transport company immedi-
ately. State date, nature of damage and whether
any damage was noticed on the shipping con-
tainer prior to unpacking. Please give the waybill
number of the shipping order.

The unit should not be placed in areas;
1. with poor ventilation
2. exposed to direct sunlight
3. with high ambient temperature or adjacent to

heat generating equipment

4. with high humidity or dust levels
5. susceptible to vibration

Unpacking

Содержание PDA200









Отзывы: