SignaMax 065-7700 Скачать руководство пользователя страница 131

Страница: 131 / 199

Hardened Managed PoE Ethernet Switch

User’s Manual 130

LEVEL <0-100> specifies the percentage of the threshold; percentage of the
maximum speed (pps) of the interface.

Example:

The following example shows setting

storm-control level

LEVEL (

) to the

interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control level 30
switch_a(config-if)#

Broadcast:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if)#

Usage:

Use

storm-control broadcast enable

command to enable broadcast traffic.

Use

no storm-control broadcast

command to disable broadcast traffic.

Command Syntax:

storm-control broadcast enable
no storm-control broadcast

4.

Example:

The following example shows setting

storm-control broadcast enable

the interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control broadcast enable
switch_a(config-if)#

Multicast:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if)#

Usage:

Содержание 065-7700








































































































































































































Результаты поиска

Содержание 065-7700

Отзывы:

Похожие инструкции для 065-7700

Бренды по названию

Популярные бренды

SignaMax 065-7700, Руководство пользователя

Результаты поиска

Содержание 065-7700

Отзывы:

Похожие инструкции для 065-7700

Бренды по названию

Популярные бренды