SignaMax 065-7700 Скачать руководство пользователя страница 132

Страница: 132 / 199

Hardened Managed PoE Ethernet Switch

User’s Manual 131

Use

storm-control multicast enable

command to enable multicast traffic.

Use

no storm-control multicast

command to disable multicast traffic.

Command Syntax:

storm-control multicast enable
no storm-control multicast

4.

Example:

The following example shows setting

storm-control multicast enable

to the

interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control multicast enable
switch_a(config-if)#

DLF:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if)#

Usage:

Use

storm-control dlf enable

command to enable destination lookup failure

traffic.
Use

no storm-control dlf

command to disable destination lookup failure

traffic.

3.

Command Syntax:

storm-control dlf enable
no storm-control dlf
dlf destination lookup failure

4.

Example:

The following example shows setting

storm-control dlf enable

to the

interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control dlf enable
switch_a(config-if)#

Static MAC Entry

Static-MAC-Entry Forward:
1.

Command Mode: Configure mode

Содержание 065-7700








































































































































































































Результаты поиска

Содержание 065-7700

Отзывы:

Похожие инструкции для 065-7700

Бренды по названию

Популярные бренды

SignaMax 065-7700, Руководство пользователя

Результаты поиска

Содержание 065-7700

Отзывы:

Похожие инструкции для 065-7700

Бренды по названию

Популярные бренды