SignalFire Sentinel-yTherm Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 13

background image

1

SignalFire Telemetry

Rev 1.6

Interface Manual

Sentinel Node
Thermocouple

SignalFire Model: Sentinel-yTherm-XXXX,

where y is TC type (K, J, etc.)

The SignalFire Sentinel Node is an Intrinsically Safe device with the following features:

-

Standard SignalFire Sentinel RS485-Modbus Node

-

RS485 connection to a Thermocouple Interface Board

-

Type K and J thermocouple boards are supported (other types on request)

-

Low power operation from an intrinsically safe high capacity lithium primary
battery pack

-

Optional solar battery system for routing nodes or rapid data collection

-

Sends data to a SignalFire Buffered Modbus Gateway

-

AES 128Bit Encryption

1
2
3
...
»

Содержание Sentinel-yTherm Series














Отзывы:

Нет отзывов

Похожие инструкции для Sentinel-yTherm Series

Бренд: Jäger Direkt Страницы: 5

Бренд: Unipar Страницы: 10

Бренд: ESP Страницы: 12

Бренд: Dakota Alert Страницы: 18

IQeye Sentinel Series

Бренд: Iqinvision Страницы: 15

treeMOTION S.light USCA

Бренд: TEUFELBERGER Страницы: 152

Бренд: Steren Страницы: 39

Бренд: Linear Страницы: 39

Бренд: DAITEM Страницы: 19

Бренд: Bircher Reglomat Страницы: 24

Бренд: i3 International Страницы: 28

VK2-3MPBIR28V12re

Бренд: Vista Страницы: 14

Бренд: Eneo Страницы: 90

Бренд: Eldes Страницы: 8

Бренд: Nexxt Страницы: 10

Бренд: jablotron Страницы: 2

IMI SENSORS Y683A101001

Бренд: PCB Piezotronics Страницы: 30

Бренд: DELTA DORE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды