SIGNALCORE SC5317A Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 39

SIGNALCORE SC5317A Скачать руководство пользователя страница 10

©2018

Rev 1.1

9

Functional Description

12  System Reset, Logic 0 to Reset Device
18  Reserved, Pull High to 3.3V or DNC
20  SRDY. This pin is serial ready for SPI

Mini-USB Connection

This is a mini-USB Type B connector for USB communication with the device using the standard USB 2.0
protocol (full speed) found on most host computers. The pinout of this connector, viewed from the front,
is shown in the following table.

PIN #

USB Function

Description

1

VBUS

Vcc (+5 Volts)

2

D-

Serial Data (neg)

3

D+

Serial Data (pos)

4

ID

Not Used

5

GND

Device Ground (also tied to connector shell)

Reset Button (Pin Hole)

Behind this pin hole is the reset button, only available on the SC5318A. Using a pin to lightly depress this
momentary-action push button switch will cause a hard reset to the device, putting it back to its default
settings. All user settings will be lost. System reset capability can also be accessed through the
communication header connector.

3

Functional Description

Overview

The SC5318A uses USB as its primary interface with an optional SPI or RS232 interface. The SC5317A is a
PXIe version of the product.

The downconverter assembly consists of 2 module parts:

•

The Signal Conversion Module contains the mixers, filters, signal amplifiers, and attenuators, also

referred to as the “signal

chain”.

This conversion module also includes a built-in LO synthesizer.

Figure 2. Proper Removal of Latching-Style Ribbon Cable Connectors

«
...
8
9
10
11
12
...
»

Содержание SC5317A








































Отзывы:

Нет отзывов