SIGLENT SPD3303X Скачать руководство пользователя | Manualshive

Страница: 10 / 45

background image

SIGLENT

2 SPD3000X QuickStart

General Inspection

Please check the instrument according to the following steps.

1. Inspect the shipping container.

Keep the damaged shipping container or cushioning material until the contents

of the shipment have been completely checked and the instrument has passed

both electrical and mechanical tests.

The consigner or carrier will be responsible for damages to the instrument

resulting from shipment.

SIGLENT

would not provide free maintenance or

replacement.

2. Inspect the instrument.

If there are instruments found damaged, defective or failure in electrical and

mechanical tests, please contact

SIGLENT

.

3. Check the accessories.

Please check the accessories according to the packing list. If the accessories

are incomplete or damaged, please contact

SIGLENT

.

«
...
8
9
10
11
12
...
»

Содержание SPD3303X














































Отзывы:

Нет отзывов

Похожие инструкции для SPD3303X

Бренд: Makita Страницы: 16

Бренд: WAGO Страницы: 78

Бренд: Harley Benton Страницы: 16

Бренд: Kamasa-TOOLS Страницы: 12

Бренд: ITech Страницы: 46

Бренд: Array electronic Страницы: 73

Бренд: MaxPro PROFESSIONAL Страницы: 50

Бренд: Aprimatic Страницы: 2

Бренд: Avdel Страницы: 3

Бренд: Michigan Pneumatic Tool Страницы: 16

Бренд: Metabo Страницы: 68

Бренд: RAMSET Страницы: 14

Бренд: Ulvac Страницы: 89

Бренд: Far Tools Страницы: 24

TRIO-PS-2G/3AC/24DC/40

Бренд: Phoenix Contact Страницы: 25

Бренд: Xinpu Страницы: 13

PolySprint NPS-1210A-1

Бренд: Nitta Страницы: 22

Clincher Fence Machine

Бренд: JoinTech Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды