system to mount the servo in place on the servo mount. Repeat
this procedure to mount the servo in the opposite wing panel.
HINGING THE AILERONS
❑
2) Note that the CA Hinges are installed, but not yet glued, in
the ailerons and wing panels. The installation process for the
hinges is the same for all of the control surfaces on this model.
a) If you removed the ailerons and hinges from the wing panels
when you tightened the covering material, reinstall them now.
First insert the five CA Hinges into the slots in the aileron. Put
two pins in the center of each hinge, up against the leading edge
of the aileron, to keep the hinges centered during the next step.
b) Now carefully insert the exposed portion of the five hinges
into the trailing edge of the wing. You will find it easiest to slide
the hinges into the slots at angle, one hinge at a time, instead of
trying to push it straight onto all the hinges at once.
c) Adjust the aileron so that the tip of the aileron is flush with
the wing tip. The ailerons should be tight against the pins in the
hinges to minimize the gap between the wing and the aileron. The
aileron is now in the proper position for permanently gluing them
in place with thin CA glue.
d) Flex the aileron down and hold it in this position. Remove
the pins from one hinge and then carefully apply 3-4 drops of Thin
CA glue directly onto the hinge in the gap. You will notice that the
glue is quickly wicked into the slot as it penetrates both the wood
and the hinge. We suggest using a fine tipped applicator on the
glue bottle to better control the flow of glue.
e) Turn the part over and glue the other side of the hinge. Con-
tinue this process until you have glued both sides of all the hinges!
Keep a rag handy to wipe off any excess Thin CA glue. (If you
get some glue smears on the plastic covering, don't worry about
them right now. Once all the hinging is done, you can clean the
smears off the covering with CA Debonder).
f) Let the glue dry 10-15 minutes before flexing the hinges. At
first you might notice a little stiffness in the joint. This will go away
after the hinges have been flexed back and forth a couple dozen
times.
INSTALL AILERON CONTROL HORNS & PUSHRODS
From the kit contents locate:
(2) Nylon Control Horns
(6) M2 x 12 mm Screws
(2) Short Pushrod Wires with M2 Hex Nut
(2) Metal R/C Clevis
(2) Nylon Snap Keepers
(2) small pieces of Fuel Tubing
❑
3) Look closely and you will see three holes pre-drilled in the
bottom of the ailerons for mounting the nylon control horns. Screw
the control horn in position on the bottom of the aileron using three
M2 x 12mm screws.
When the tips of the screws begin to emerge at the top surface of
the aileron, add the control horn's nylon retaining plate. The
aileron will be sandwiched between the control horn on the bottom
and the retaining plate on the top. Continue turning in the screws
until the horn and retaining plate are snug against both surfaces
of the aileron. Do not over tighten the screws and crush the wood.
The excess length of the screws that is extending past the retain-
ing plate can be cut off with a pair of side cutting pliers or ground
down with a rotary tool with a cutoff disc.
❑
4) Next assemble and install the aileron pushrods.
a) Slide a short piece of Fuel Tubing onto the small end of the
Metal R/C Clevis. Screw the Hex Nut on the Aileron Pushrod Wire
all the way up to the end of the threads. Then screw the metal
clevis halfway onto the threaded end of the Aileron Pushrod Wire.
b) Clip the metal clevis into the last hole in the nylon control
horn. Lay the other end of the pushrod wire over the outer hole
in the servo arm. Use a felt tip pen to mark the wire where it
5