❑
2 each PM4 x 35 mm Phillips Head Bolts - Main Wheel Axles
❑
4 each M4 Hex Nuts - Main Wheel Axle Attachment
❑
10 each M4 Washers - Main Wheel Axles (6), Motor Mount
Bolts (4)
❑
2 each 4mm Wheel Collars With Set Screws - Main Wheel
Attachment
WIRE PARTS:
❑
1 each Pre-Bent 3mm Elevator Joiner Wire
❑
1 each Pre-Bent 2.0 mm Tail Wheel Wire
❑
2 each 1.8mm Dia. x 19.7cm Bright Wire, Threaded Both
Ends - Upper Tail Supports
❑
2 each 1.8mm Dia. x 15.5cm Bright Wire, Threaded Both
Ends - Lower Tail Supports
❑
2 each 2-56 X 1-1/4" Threaded One End - Rudder & Elevator
Servo Control Rods
❑
2 each 2-56 X 3-1/2" Threaded One End - Rudder & Elevator
Control Horn Rods
❑
2 each 2-56 X 4-1/2" Threaded One End - Aileron Pushrods
❑
1 each .065 Dia. x 18" Braided Throttle Cable
MOLDED PARTS:
❑
2 each 1/8" O.D. x 22" Nylon Rudder & Elevator Pushrods
❑
2 each Nylon Control Horns - Rudder & Elevator - Medium
RIGHT
❑
1 each Nylon Control Horn - Aileron - Small RIGHT
❑
1 each Nylon Control Horn - Aileron - Small LEFT
❑
5 each Nylon 2-56 RC Links - Rudder & Elevator (2),
Ailerons (2) & Throttle (1)
❑
8 each Molded Plastic Support Ends - Tail Support Wire Ends
❑
1 each 2-1/4" Spinner Assembly, White, With Inserts and
Mounting Screws - P/N SIGSP22511
❑
1 each 4-40 x 1" Slotted Nylon Bolt - Canopy/Hatch
Attachment
❑
4 each Clear Silicon Washers - Canopy Attachment
MISCELLANEOUS:
❑
1 each Hardened Aluminum Main Landing Gear
❑
1 each Hardened Aluminum Tube Main Wing Joiner - 18 mm
Diameter x 38.6 cm
❑
1 each Pre-Bent Tail Wheel Wire Bracket
❑
1 pair
2-3/4" (70mm) Diameter Main Wheels
❑
1 each 1.0" (25mm) Diameter Tail Wheel
❑
17 each CA Hinges - Rudder 3, Elevator 6, Ailerons 8
❑
1 set
Adjustable Width 40-Size Motor Mounts
❑
1 each Fuel Tank, 260cc (8.8 oz.) With All Fittings
❑
1 each 3 mm Plywood Aileron Position Guide (APG)
❑
1 each 5mm Dia. x 150mm Hardwood Dowel - Rear Wing
Positioning Dowel
❑
2 each Black Foam Rubber - 10mm x 80mm x 200mm -
Radio & Fuel Tank Packing Material
❑
1 each #64 Rubber Band - Wing Attachment
❑
1 each Decal Set
❑
1 each Assembly Manual
ASSEMBLY:
We have found it helpful in the assembly of this pre-covered model
to be sure that our workbench is covered with an old blanket or soft
foam pads to prevent denting, scratching, etc.
WINGS:
The two wing panels in your kit are virtually ready to use, with the
exception of installing a servo in each panel, hinging the ailerons
and attaching the linkages. To do this, you must know which side
of the panel is the bottom. Hold one of the panels to the light. The
bottom of the wing panel will have a 1" x 2-1/4" rectangular servo
bay opening showing just beneath the white covering. Remove the
ailerons and the hinges from both wing panels, setting them aside
for now.
❑
1) Use your hobby knife and a sharp #11 blade to open the
aileron servo bay. To make the neatest possible job, we suggest
cutting each corner of the opening at a 45° angle toward the
middle of the opening. Then make a cut at the middle of the
opening, connecting with the four previous corner cuts.
The four sides of the servo bay opening can now be covered using
a small trim seal type iron. Use your hobby knife to trim off the
excess covering material from inside the bay. Repeat this process
3