manualshive.com logo in svg

SIG Antoinette 1909, Руководство пользователя, Страница: 3 / 30

Поделиться
Скачать
SIG Antoinette 1909 Скачать руководство пользователя страница 3

. 

Radio Equipment, Speed Controller, Battery Pack, And Connectors

 
One of the very reasons that indoor models such as the Antoinette are now possible is the fairly recent availability of good 
quality, reasonably priced light-weight micro receivers, servos, and speed controllers (ESC's). Up to this time, such equipment 
was only available from small, highly specialized sources at relatively high prices.

 
Here are the airborne system components we've used in the Antoinette. 
 

Item

Weight

Maxx Products (MPI) #MX-6800 Pico 4-Ch Micro Receiver, w/crystal

8 grams

Maxx Products (MPI) #MX-30 Pico Servos

7 grams each

Maxx Products (MPI) #MX-9104 Micro ESC (Electronic Speed Control) 1 gram
7-cell 350mAh Ni-Cd (nicad) Battery Pack

95 grams

7-cell 500 mAh NiMH (nickel metal hydride) Battery Pack

96 grams

 
These are the components that are shown in this manual and on the plans. We did not use an On/Off switch in this airplane 
because of weight considerations. The battery is simply plugged and unplugged from the ESC before and after each flight. 
Different brands of receivers, servos, and ESC's may be usable with this design, provided they are the same weight and size or 
lighter. For obvious reasons, standard size radio components cannot be used with the Antoinette.

 
A 7-cell 350mAh Ni-Cad battery pack is used in the Antoinette to provide good flight 
duration. With throttle management, this battery pack will keep the Antoinette flying for 
anywhere from 8 to 12 minutes. We've also used 7-cell 500 mAh NiMH (Nickel Metal 
Hydride) battery packs with good results. In general, the difference between this type 
of cell and the 350 mAh NiCad cell is that the NiMH pack seems to deliver a little less 
power with some incremental increase in duration. Both types of cells weigh the same, 
so they are both usable. Last, the battery pack should be configured in the "hump" 
shape - four cells on the bottom, three cells on top. This layout offers the most mass in 
the least amount of space and this is very helpful when making small changes in the 
C.G. location, if needed.

 

 
For maximum flight performance, indoor R/C 
models require attention to the weight of 
everything they must carry aloft, including 
connectors. We used and liked the small 2-
prong Dean's connectors for connecting the 
battery pack to the ESC. Recently, Cloud 9 
Micro R/C announced the availability of their 
new micro connectors. We've seen and used 
these and can recommend them for use with 
the Antoinette. There are many other 
connectors available on the market. Be sure to 
choose your connectors with weight, size, and 
efficiency considerations in mind. 
 
Last, our radio systems include excellent 
transmitters, providing us with features such as 
servo throw adjustments (EPA), servo 
reversing, servo sub-trim adjustments, etc. Our 
trusty Airtronics® RD-6000 Sport transmitters 
and the equivalent HiTec units have taken care 
of all these needs.

 

Required Tools

A selection of glues 

SIG Thin CA  

SIG Medium or Thick CA  

SIG Thin CA Applicator Tips  

SIG Kwik-Shot CA Accelerator  

Heat-Activated Covering Adhesive, 
such as SIG Stix-It or Solarfilm Balsaloc. 

Assorted drill bits, including 

.031" (1/32" or # 68)  

.046" (3/64" or # 56)  

.063" (1/16" or # 52)  

.078" (5/64" or # 47)  

.093" (3/32" or # 42)  

.109" (7/64" or # 35) 

A selection of hand tools, such as 

Regular size and miniature screwdrivers  

Regular size and miniature pliers (flat nose, needle nose, round nose)  

Tweezers and/or small hemostats  

Hobby knife with sharp #11 blades  

Sandpaper - assorted gritsModeler’s "T" pins  

Power drill and hand "pin vise" (for small diameter drill bits) 

 

Paint

 
Since fuel proofing is not an issue with electric powered airplanes, the only reason to paint any part of the Antoinette is to 
improve the scale appearance of the model. And because light weight is so important in an indoor model, we’ve tried to keep 
the painting on the Antoinette to a minimum. Too much paint, or the wrong kind of paint, can add unnecessary weight in a hurry.

Содержание Antoinette 1909































Отзывы:

Нет отзывов