Sifos Technologies PhyView PVA-3000 Скачать руководство пользователя страница 65

Страница: 65 / 134

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
65

3.16.4.

Example 4: Measure 4-pair PSD and SNR of Calibration Partner linked at 1000Base-T

This task is performed using the

Link Config

and

Meters

menu. Port 1,1 should be connected to Port 1,2 using the

Sifos furnished patch cable.

Hint: If test port is Slot 1, Port 1, then Calibration Partner port is Slot 1, Port 2.

Menu

Task

Screen Shot

Port Select

Select the port to configure.

Click on

Port 2

Slot 1

on the

Slot Port

Select

menu.

Link Config

Reset calibration partner port to default
TEST PHY configuration

Select the

Link Config

Tab

Click

Reset Test PHY

Port Select

Select the test port to use for
measurements

Click on

Port 1

Slot 1

on the

Slot Port

Select

menu.

Link Config

Configure the test port speed, polarity and
duplex settings.

Select the

Link Config

Tab.

Select

Nominal Fixed

under

Test PHY

Click

Apply Rx Level

Select

1000BaseT

under

Link Speed

Select

Automatic

under

Link Duplex

Select

Automatic

under

Link Polarity

Click

Arm Configuration

Click

RE-LINK

Meters

Measure SNR.

Select the

Meters

Tab

Select

1000

under

Link Speed

Select

SNR

under

Meter Type

Select

All

under

Pair(s)

Click

Measure

Meters

Measure PSD.

Select the

Meters

Tab

Select

1000

under

Link Speed

Select

PSD

under

Meter Type

Select

All

under

Pair(s)

Click

Measure

Expect

–2.6dB

Flat Frequency

Response

Содержание PhyView PVA-3000







































































































































Результаты поиска

Содержание PhyView PVA-3000

Отзывы:

Похожие инструкции для PhyView PVA-3000

Бренды по названию

Популярные бренды

Sifos Technologies PhyView PVA-3000, Справочное руководство

Результаты поиска

Содержание PhyView PVA-3000

Отзывы:

Похожие инструкции для PhyView PVA-3000

Бренды по названию

Популярные бренды