manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Справочное руководство


Поделиться
Скачать
background image

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 
134 

seconds for the 10/100/1000Base-T 
test in Figure 6.1 and 29.5 seconds 
per port in the 10/100Base-T test 
cycle of Figure 6.2. 

 

In Figure 6.3, the upper report 
depicts marginal transmission 
performance in the area of return 
loss.   Marginal does not necessarily 
mean non-compliant to IEEE 802.3, 
however it does indicate that the 
performance is near the 802.3 limit 
line.   The lower report (segment) 
indicates a 1000Base-T Receiver 
Integrity failure where the port-
under-test failed to perform given the 
impairments described for 
1000Base-T earlier. 

 

 

 

6.4.3. 

Managing Test Limits and Link Delay Tolerances in 

pva_veriphy 

Although 

pva_veriphy

 

is furnished as a compiled program file, users may modify certain decision criteria utilized 

within 

pva_veriphy

, namely the criteria that assign summary results based on quantitative parametric results and the 

maximum tolerated link-up times.   A text file, 

pva_veriphy_limits.txt

, is provided within the 

…Sifos/PSA1200/Config/env

 subdirectory to effect this control.   

 
The 

pva_veriphy_limits.txt

 

file is organized as a table 
shown in Figure 6.4.  The 
Link Stability Test (TEST1) 
will by default produce the 
summary result “GOOD” if 
Link Stability measures at 
least 99% 

and

 SNR 

measures at least 31.1 dB.   
The test will report 
“MARGINAL” if the Link 
Stability measures between 
97% and 99% 

or

 the SNR 

reads between 27.1 dB and 
31 dB.  Finally, if Link 
Stability measures below 
97% 

or

 SNR measures 

below 27.1 dB, the 
Summary will report 
“FAIL”. 
 
Similarly, the decision logic for the Transmission Test (TEST2) requires that as many as 13 parameters meet or exceed 
certain criteria in order to be deemed “GOOD” and will produce a “FAIL” if any one of those parameters fall short of 
the “MARGINAL” criteria.   Users wishing to alter summary criteria should be aware that only the numeric values in 
this file should ever be modified and that it is critical that the literal criteria names, e.g. TEST2_GOOD_100, always be 
preserved as the first entry on each row. 
 
The 

pva_veriphy_limits.txt

 file also includes default timing parameters for the maximum expected multi-port link 

times associated with 10, 100, and 1000Base-T link-ups both with “clean” unimpaired connections and with maximum 
802.3 insertion loss connections.    These times won’t affect test results or test time in any way unless the ports-under-
test take longer than the time specified to effect link-ups at the given link rates and impairment conditions.   So, for 
example, if an Ethernet switch might take longer than 12 seconds to link up to 6 ports to 1000Base-T, then the 
LINKTIME_1000_CLEAN entry could be increased to a larger value. 
 
The 

pva_veriphy

 

test program will run in the absence of the 

pva_veriphy_limits.txt

, however if the file is present, the 

values in the file will always override the default values for summary criteria and link-up times. 

Figure 6.3 

6-Port 10/100/1000Base-T Test Reports with Performance Issues 

Figure 6.4 

pva_veriphy_limits.txt File in the …/env/ Directory 

Содержание PhyView PVA-3000







































































































































Отзывы:

Нет отзывов

Похожие инструкции для PhyView PVA-3000

ZHYQ GND15 Quick Start Manual preview
GND15
Бренд: ZHYQ Страницы: 6
Lasertec TruPulse L2 Quick Reference Field Manual preview
TruPulse L2
Бренд: Lasertec Страницы: 21
H-Star SS-90X Owner'S Manual preview
SS-90X
Бренд: H-Star Страницы: 36
Lasertec HV3R Instruction Manual preview
HV3R
Бренд: Lasertec Страницы: 28
Raytech TR-MARK III Instruction Manual preview
TR-MARK III
Бренд: Raytech Страницы: 7
Elcontrol Vip 396 485 Addition To The User Manual preview
Vip 396 485
Бренд: Elcontrol Страницы: 7
Vaisala K-PATENTS PR-43 User Manual preview
K-PATENTS PR-43
Бренд: Vaisala Страницы: 54
Hach DR/2000 Instruction Sheet preview
DR/2000
Бренд: Hach Страницы: 4
JensPrima innoCon 6800O Operating Instruction preview
innoCon 6800O
Бренд: JensPrima Страницы: 20
Larson Davis SoundExpert LxT User Manual preview
SoundExpert LxT
Бренд: Larson Davis Страницы: 307
LaserLiner 082.214A Manual preview
082.214A
Бренд: LaserLiner Страницы: 64
TE Connectivity 549 AC Installation And Operating Instructions preview
549 AC
Бренд: TE Connectivity Страницы: 3
Leica Rangemaster CRF 1000 Instructions Manual preview
Rangemaster CRF 1000
Бренд: Leica Страницы: 118
SloanLED 601146 Installation Manual preview
601146
Бренд: SloanLED Страницы: 3
S&T TPMS1209C01 User Manual preview
TPMS1209C01
Бренд: S&T Страницы: 23
BGS technic BGS 8639 Instruction Manual preview
BGS 8639
Бренд: BGS technic Страницы: 16
Trotec OZ-ONE Manual preview
OZ-ONE
Бренд: Trotec Страницы: 8
GW Instek LCR-800 Series User Manual preview
LCR-800 Series
Бренд: GW Instek Страницы: 91

Бренды по названию

Популярные бренды

Загрузить еще бренды