background image

 

 

 

Building Technologies  

- 20 - 

TEL50.GSM 

 

7.2  Modification of Input-Output identification string 

In this section the User can modify the identification string (ALIAS) for the device inputs/outputs. New identification strings will 
support the factory’s ones that remain active. Queries or commands can be sent using either factory’s strings or ALIAS set by 
the user.

 

If no changes are made, the factory settings are maintained.

 

The defined alias will have a maximum length of 10 alphanumeric characters ( 0÷9, A÷Z ). Observe the syntax indicated below. 
Note that the characters “space (blank), +, -, _, etc”, are not included and, consequently, are not recognized by the device.

 

 

Inputs - Outputs Factory 

setting Any 

modification Example 

Incorrect 

 

example 

Alarm input 

IN1 

max 10 characters ( 0÷9, A÷Z). 

ALARM 

ALARM 1 

Relay output 1 

OUT1 

max 10 characters ( 0÷9, A÷Z). 

BOILER 

PUMP+1 

Relay output 2 

OUT2 

max 10 characters ( 0÷9, A÷Z). 

LIGHTS 

HOME LIGHTS 

Temp. sensor input 

TEMP 

max 10 characters ( 0÷9, A÷Z). 

TEMPEXT 

TEMPERATURE 

 

Some examples of correct syntax for modifying the identification strings are shown below. 

 

[ALIAS] 

SMS command SMS 

reply Action 

ALIAS IN1=ALARM 

IN1=ALARM 

identification input 1 with “ALARM” 

ALIAS OUT1=BOILER 

OUT1= BOILER 

identification relay output 1 with “BOILER” 

ALIAS OUT2= LIGHTS 

OUT2= LIGHTS 

identification relay output 2 with “LIGHTS ” 

ALIAS ANALOG=TEMPEXT 

ANALOG=TEMPEXT (*) 

identification analogue input with “TEMPEXT” 

(*) factory preset  ANALOG=TEMP 

Содержание TEL50.GSM





























Отзывы: