Siemens TEL50.GSM Скачать руководство пользователя | Manualshive

Страница: 13 / 28

background image

Building Technologies

- 11 -

TEL50.GSM

4.3 Connection of stilo antenna

The TEL50.GSM is supplied with its own dual band stilo antenna with the following characteristics:

PARAMETER

CHARACTERISTICS

Profile

Dual-Band GSM

900MHz band

890-960MHz

1,800MHz band

1710-1,880MHz

Impedance

50 ohm

WSVR

<= 1:1,5

Type

Omnidirectional

Radiation diagram on horizontal plane

Circular @ ± 0.5dB

Radiation diagram on vertical plane

± 35° @ 3dB

Connector

SMA (male)

4.4 Connection of external antenna (optional)

In the top part of the TEL50.GSM, there is an RF female SMA connector that is normally connected to the specially supplied
stilo antenna. Ensure that the antenna connector is securely fastened.

In some operating conditions, the stilo antenna does not permit optimum reception of the RF signal and, for this reason, the
TEL50.GSM can also be used with a high gain directive or omnidirectional external antenna (optional). If this is necessary,
remove the stilo antenna connector and connect the external antenna one.

«
...
11
12
13
14
15
...
»

Содержание TEL50.GSM





























Отзывы:

Нет отзывов

Похожие инструкции для TEL50.GSM

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: idatastart Страницы: 24

Бренд: Omegalink Страницы: 2

Бренд: Rain Bird Страницы: 138

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды