Siemens SpeedStream 6500 Series Скачать руководство пользователя страница 11

Страница: 11 / 98

Chapter 2

Installation

This chapter covers the physical installation of the SpeedStream Gateway.

Minimum System Requirements

•

DSL service and an Internet access account from an Internet Service Provider (ISP).

•

Network cables for each device you intend to connect to the Gateway.

•

TCP/IP network protocol must be installed on all computers.

•

For USB connection to the Gateway, the following operating systems are supported:

•

Windows 98, 98SE

•

Windows

2000

•

Windows ME or XP

•

Mac OS versions 8.6 through 10.2.4

Note:

Your configuration may vary slightly from the instructions and illustrations in this chapter. Refer to

your service provider’s documentation, or contact them with questions regarding your specific
configuration.

Hardware Installation

You may position the SpeedStream Gateway at any convenient location in your office or home. No
special wiring or cooling requirements are needed; however, you should comply with the safety guidelines
specified in the

General Safety Guidelines

section.

Basic Installation Procedure

Install line filters if necessar

Connect the cables

Install USB drivers if necessary

Configure network settings on your computer

Configure the Gateway via the Web-based management interface

6. Reboot the computer if prompted. Whenever you are required to reboot the Gateway, allow five

seconds between turning off the unit and powering it back on.

Содержание SpeedStream 6500 Series



































































































Результаты поиска

Содержание SpeedStream 6500 Series

Отзывы:

Похожие инструкции для SpeedStream 6500 Series

Бренды по названию

Популярные бренды

Siemens SpeedStream 6500 Series, Руководство пользователя

Результаты поиска

Содержание SpeedStream 6500 Series

Отзывы:

Похожие инструкции для SpeedStream 6500 Series

Бренды по названию

Популярные бренды