Siemens Siwarex U Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 89

Siemens Siwarex U Скачать руководство пользователя страница 62

7BCOMMUNICATION IN SIMATIC S7

8.4.7

CMD_ERR:= "DB_SIWA_U".bo_CMD_ERR, output, BOOL

The bit notifies the user for a cycle that his command has not been executed. The
bit is set for one cycle (edge) only. In the same cycle, the cause can be shown with
the variable CMD_ERR_C:= "DB_SIWA_U".b_CMD_ERR_CODE. The number is
itemized in the table "Data and operator errors" in Chapter

. When no error code

is specified, it must be checked in the same cycle in
"DB_SIWA_U".b_FB_ERR_CODE whether an FB error is present.

8.4.8

CMD_ERR_C:= "DB_SIWA_U".b_CMD_ERR_CODE, output, BYTE

For a command that is not executed (Finished with errors), the error number is
output here. The number that is output is decoded in table "Data and operator
errors" in chapter

. The value remains in the output until the next command is

triggered. The evaluation is to be performed when the set bit
CMD_ERR:= "DB_SIWA_U".bo_CMD_ERR appears. When no error code is
specified, it must be checked in the same cycle in
"DB_SIWA_U".b_FB_ERR_CODE whether an FB error is present.

8.4.9

REF_COUNT1:= "DB_SIWA_U".b_CYCLE_COUNT_CH1, output, BYTE

The current output values, which are prepared as output variables of the FB
SIWA_U, are read out from the FB cyclically via the peripheral area. SIWAREX U
updates the counter internally in a 20 ms rhythm. Each updating is given a serial
number, which can be used as a time stamp in the SIMATIC CPU. The number can
be between 0 and 255.

8.4.10 SC_STATUS1:= "DB_SIWA_U".b_SCALE_STATUS_CH1, output, BYTE

The current status of the scale is output via this variable. The meaning of the status
bits corresponds to the status byte in DR31.

8.4.11 ASYNC_ERR1:= "DB_SIWA_U".w_OPR_ERR_MSG_CH1, output, BYTE

Via this word the current operating errors (asynchronous errors) are displayed.
This error display is automatically reset with the correction of the error.

8.4.12 GROSS1:= "DB_SIWA_U".i_GROSS_WEIGHT_CH1, output, INT

Via this variable the user is provided with the current weight value for channel 1.

8.4.13 FLT_RAW1:= "DB_SIWA_U".w_ADC_VALUE_FILTERED_CH1, output, INT

Via this variable the user is provided with the current digital filtered value from the
ADC for channel 1.

8-54

SIWAREX U

«
...
60
61
62
63
64
...
»

Содержание Siwarex U


























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды